Safety regulations

1. Any repairs or maintenance of a vehicle should be carried out in a spacious, well-ventilated and lit room.

2. Workshop (hoisting machines, machine tools, power tools) should be specifically adapted to carry out repair operations on the vehicle (for example, to power portable lighting sources, it is desirable to use a low voltage - 36 or 12, not 220).

3. Do not smoke or use an open flame in the area where the car is located, lubricants, etc.

4. When working with plumbing tool wear gloves - they not only protect your hands from dirt and scratches and cuts.

5. Any work from the bottom of the car follow the safety glasses.

6. For the body repair (putty, painting, polishing) Wear a dust mask and provide additional ventilation.

7. The works associated with the removal, installation of heavy components and assemblies of the car, follow with the assistant.

8. Tanks with fuel and lubricants and paints stored in the workshop, should always be tightly closed. Do not allow such materials in the area falling sparks when using cutting tools.

9. Do not allow oils (especially waste), anti-freeze and the electrolyte exposed skin. In case of contact wash off as soon as possible with soap solution.

10. Do not use for cleaning hands skin gasoline, diesel fuel, solvents, etc.

11. Remember that improper maintenance of electrical equipment and fuel equipment may result in fire. If you do not have confidence in their knowledge of services these systems, it is better to consult specialists. If, however, decided to perform the work yourself, follow all warnings and precautions.

12. Take special care when repairing vehicles equipped with airbags or pretensioners. Do not attempt to repair the components of these systems (electronic airbag control unit, air bag modules, steering wheel, impact sensors, seat belt pretensioners, etc.) as well as improper performance of work may trigger these devices and, as a consequence, serious injury. When working in the area of the location of these devices carefully review all of the recommendations and warnings.

13. Tools and equipment used in the repair of the vehicle must be in good condition. Particular attention should be given to the insulation of electrical wires.

14. When servicing vehicles equipped with an air conditioning system does not allow depressurization of the system, since it contained toxic refrigerant.

In order to secure the lifting jack must be performed as follows.

1. Place the vehicle on a flat, hard surface.

2. Before lifting the car free of foreign objects. Beforehand take away from the trunk of everything you need for repair (spare parts, tools), as access to the raised vehicle can be difficult or impossible.

3. Jack place only under the places that are designed for this purpose. Power tailgate at these places specially thickened and have increased durability.

4. Place a wheel chocks under the wheels of the car on the side opposite to rise.

5. In order to prevent subsidence and indentation in the ground jack placing it on the board (see 20h20h2).

6. Move the thrust head on the body of the car. When this jack to stand perpendicular to the supporting surface.

7. Before a jack to raise the vehicle to the desired height, again carefully check to see whether he banked in any direction.

8. Supports should be installed only as a specially designed to lift the car seat. Between the support and the car body enclose a rubber or wooden lining.

9. Place the tripod support so that its two legs are side vehicle body, and one - from the outside.

When used to lift the vehicle lift, observe the following safety requirements.

1. During the lifting and lowering of the car is prohibited to be close to him in order to avoid an accident.

2. If there is a danger of falling car immediately leave the danger zone.

3. Correctly position the center of gravity of the vehicle on the hoist to prevent it from falling.

4. Take care of the feet, so as not to squeeze their legs lift or wheels when the vehicle is lowered.

5. Do not use excessive force to controls lift.

6. Manage the lift must only qualified personnel.

7. Avoid excessive rocking of the car on a lift.

8. Paws lift place only under the places that are designed for this purpose. Power tailgate at these places specially thickened and have increased durability.

9. When removing heavy components and assemblies from the vehicle mounted on the lift, install additional support.