REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Hyundai
	Accent
		Instructions
		Engine
		Greasing system
		Cooling
		Control, reduced toxicity
		Fuel system
		Ignition system
		Coupling
		Transmission
		Axes and power shafts
		Suspension
		Steering
		Brakes
		Body
			Technical data
			Adjusting the hinges of a cowl
			The trunk lid
			Adjusting tailgate
			The front door
			Backdoor
			Moldings
			Sunroof
			Door mirror
			The center console
			Dashboard
			Finishing the ceiling
			Rear shelf
			Upholstery trunk
			Interior upholstery
			Windshield
			Rear window
			Front bumper
			Rear bumper
			Backseat
			Front seat
			Troubleshooting
		Air
		Electrical equipment
		Appendix
		Wiring

printable version

Windshield

1 - spacer windscreen;
2 - windshield molding;
3 - inside rearview mirror;

4 - the windscreen;
5 - lining windscreen.

Withdrawal

PERFORMANCE ORDER

	1. Before removing the windshield, remove the following items: - Upper pillar trim; - Rear-view mirror; - The wiper arms; - Cover the upper part of the bonnet; - Molding of the windshield.
	2. The special tool 09861-31100 cut sealant windshield mounting.
	3. If the glass will be installed again, leave a layer of sealant on the glass and body. Mark the position of the glass in the back of the car.
	4. The special tool 09861-31400 remove the windshield from the vehicle.

Setting

PERFORMANCE ORDER

	1. The special tool or knife cut off the old sealant layer to a thickness of 2 mm around the perimeter of the frame and windshield.
A warning Be careful not to remove the sealant is greater than necessary, as well as not to damage the paintwork of the vehicle.
2. Degrease the treated surface.
	3. Attach the windshield to the window opening, and at four points on the body mark the installation of the glass.
	4. Stick the rubber pad to the inner surface of the windshield. The height of the sealant layer: Above: 13.5 mm On both sides: 13.5 mm Bottom: 27 mm
	5. Install the windshield.
	6. Apply a thin coat of primer on the glass outside of the pad for the windshield.
A warning Do not touch the sealant by hand. In place of touch sealant hand it can not provide a reliable connection and in this place possible leaks after the installation of the glass. Do not apply primer on glass, designed for the body.
	7. Apply a thin coat of sealant to the initial application, extending around the perimeter of the glass. The glass must be set within 10 minutes after application of the primer.
8. Lay the glue into the syringe and put it on the edge of the windscreen.
A warning Apply the adhesive for 5 minutes after the application of a glass primer.
9. special tools or suckers, set the glass on the window opening according to earlier put labels and press the glass to the window opening.
	10. spatula to remove excess adhesive. Fill in all the sinks and void on the perimeter of the windshield.
11. Directing the stream of water on the windshield, check the tightness of the installation. Do not point the fresh sealer jet of water under high pressure.
	12. In the presence of leaks dry the affected area and apply a sealant.
A warning Do not operate the vehicle for 4 hours after installation of the glass. After installation of the windscreen keep it in the first hour.
	13. Reinstall all previously removed elements.
A warning Within 2-3 days after installation of the windscreen do not slam doors. Avoid driving on rough roads where the car body is subjected to intensive twisting.

« previos page
Interior upholstery

next page »
Rear window