The wheel hub and knuckle

1. Loosen the wheel nuts and nut of the drive shaft when the vehicle is on wheels.
2. Position the front of the car on support and remove the wheel.
3. Remove the brake caliper. To do this, remove the two shown in the illustration below the bolt. Tie Caliper wire segment to the front suspension. Do not slide on the hose sagging.

Both the arrows bolts hold the brake caliper.

4. Remove the cotter pin from the castellated nut steering rod, loosen the nut and separate the hinge suitable puller from the steering arms (see. Illustration below). To avoid damage to the thread, you can screw the nut onto the upturned thumb so that it is flush with it.

Squeezing the ball stud steering rod from lever steering rod using a special puller.

5. Loosen the nut on the top side of the steering knuckle and remove the guide pin of the knuckle of engagement with the upper arm. As you can see, the compounds are distinguished from previous models of cars Nissan. Click whole knuckle down until he takes the position shown in the illustration below.

Tilt steering knuckle in the kit, and then knock down the collar of the hub.

6. Screw the nut on the drive shaft until the outer side will be flush with the shaft and the shaft is slightly light-alloy hammer hammer inside to loosen it from the bearing hub.
7. On the bottom side of the steering knuckle remove the nut on the ball joint and control arm ball joint to separate the connection using a stripper. Depicted in the illustration below puller suitable for suspension ball joints.

Check the fluid level in the compensation tank servo

1 - warm 2 - Cold

7. Remove the knuckle of the front suspension. Remove the brake disc.
8. If you want to remove the knuckle together with the drive shaft, drain the transmission oil (remove the plug and place a container).
9. Depress the drive shafts of the gearbox, as described in Chapter clutch and drive shafts for the left and right shafts, as well as manual or automatic transmissions.
10. Remove the hub knuckle and driveshaft from the vehicle or leave the drive shaft in the gearbox and remove a rotary fist with a nave from the drive shaft.

1. Unscrew the nut and remove the hub drive shaft from the hub, if it is installed.
2. Hold the steering knuckle in a vise and knock out light-alloy hub rod from the back side. If knocked out of the hub knuckle bearing should always be replaced. The inner bearing race remains on the hub should be removed and a suitable puller.
3. Remove the retaining ring on the outer side of the knuckle by means of special tongs. On the reverse side, remove the seal using a screwdriver and remove the second lock ring. Intersections in the retaining ring pliers facilitate installation.
4. Put knuckle under the press and press out the bearing from outside to inside. To drive out the bearing using pipe section. Thoroughly clean all parts. Bearings should always be replaced with collars, as they run in on one another. Steering knuckle can only be checked by using a magnetic device.

1. Thoroughly clean the grease hole knuckle and the outside of the bearing hub and insert the inner retaining ring into the groove of a rotary fist.
2. Press in a new bearing from the outside to the knuckle, until it is attached to the retaining ring. At the same time apply a force to the outer cage of the bearing hub.
3. Insert an external lock ring into the groove. Make sure that the snap ring sat perfectly around the entire circumference.
4. Grease the sealing lips of both shaft seal and grease hammer front and rear knuckle, without damaging them in the process. Wipe off excess lubricant.
5. Put the knuckle on the table press and press-fit into the hub bearing and the steering knuckle. Be sure to check that the pressure does not exceed the pressing of 3 tons.
6. Now check the bearing preload. To do this, put the knuckle on the table press and increase the load on the outside of the hub to 3.5 -5.0 tons. Hold the load several times move the steering knuckle from side to side. Stub must rotate without binding, despite the load.