 printable version
Technical data
Name | Nominal values | Limit values | | Total information | Type | Terraced, two camshafts | | Number of cylinders | 4 | | | Bore | 75.5 mm | | | The piston stroke | 83.5 mm | | | Displacement | 1495 cm 3 | | | Compression ratio | 100 | | | Operating procedure of cylinders | 1-3-4-2 | | | Engine speed at idle | 750 ?� 100 min -1 | | | Ignition timing on speed | 9 ?� 5 ?� / 800 min -1 | 9 ?� 5 ?� / 800 min -1 | | The moment of opening or closing the valve | The intake valve | Opening BTDC | 5 | | | Closing after BDC | 35 ?� | | The outlet valve | Closing ATDC | 35 ?� | | | Closing after BDC | 5 | | Valve overlap | 10 | | | Cylinder head | The flatness of the mating surface | 0.03 mm | 0.08 mm | | The flatness of the mounting surface collectors | 0.15 mm | 0.2 mm | | Increasing the diameter of the holes for the installation of the valve seat | The intake valve | 0,3 mm mm 29,8-29,821 | | | The outlet valve | 0,6 mm mm 30,1-30,121 | | The intake valve | 0.3 mm 27,3-27,321 | | The outlet valve | 0,6 mm mm 27,6-27,621 | | Increasing the diameter of the holes for the installation of the valve guide (intake and exhaust) | 0.05 mm | 11,05-11,068 mm | | | 0.25 mm | 11,25-11,268 mm | | 0.50 mm | 11,50-11,518 mm | | Camshaft | The height of the cam | The intake valve | 43.4484 mm | 42.9484 mm | | The outlet valve | 43.8489 mm | 43.3489 mm | | The diameter of the neck | 27.0 mm | | | Oil bearing play slip | 0,035-0,072 mm | | | End-play | 0.1-0.2 mm | | | Valve | The length of the valve | The intake valve | 91.7 mm | | | The outlet valve | 92.3 mm | | Valve stem | The intake valve | 5,955-5,97 mm | | | The outlet valve | 5,935-5,95 mm | | The thickness of the valve plate | The intake valve | 1.1 mm | 0.8 mm | | The outlet valve | 1.3 mm | 1.0 mm | | The gap between the guide and the valve stem | The intake valve | 0.03-0.06 mm | 0.1 mm | | The outlet valve | 0.05-0.08 mm | 0.15 mm | | The diameter of the valve guide | The intake valve | 12.8 mm | | | The outlet valve | 12.8 mm | | Increased size | 0.05, 0.25, 0.50 mm | | Width of a working facet of the valve seat | The intake valve | 0.8-1.2 mm | | | The outlet valve | 1.3-1.7 mm | | Corner of a working facet | 45 ?� | | | Increased size | 0.3, 0.6 mm | | | Free length of the valve spring | 44.0 mm | | | The length of the valve spring under load | 21.6 kg / 35 mm41,5 kg / 27.2 mm | | | Perpendicular valve spring | 15 | | | Cylinder block | Bore | 75,50-75,53 mm | | | Roundness and taper | Less than 0.01 mm | | | The clearance between the piston and cylinder | 0,025-0,045 mm | | | Piston | Diameter | 75,465-75,495 mm | | | Actual size | 0.25, 0.50, 0.75, 1.00 mm | | | Piston rings | The gap in the groove of the piston | 0,04-0,085 mm | 0.1 mm | | The gap in the castle | ?��1 | 0.20-0.35 mm | 1.0 mm | | ?��2 | 0,37-0,52 mm | 1.0 mm | | Scraper ring | 0.2-0.7 mm | 1.0 mm | | Actual size | 0.25, 0.50, 0.75, 1.00 mm | | | Rod | Twisting | 0.1 mm | | | Bend | 0.05 mm | | | Axial clearance on crankshaft | 0,100-0,250 mm | 0.4 mm | | Bearing rod | Gap | 0,024-0,042 mm | | | Reduced size | 0.25, 0.50, 0.75 mm | | Crankshaft | The diameter of the crankpin | 45 mm | | | The diameter of the main journal | 50 mm | | | Deflection | Not more than 0.03 mm | | | Roundness and taper of the necks | Not more than 0.01 mm | | | End-play | 0,05-0,175 mm | | | The reduced size of the crankpin 0.25 mm | 42,225-44,24 mm | | | The reduced size of the crankpin 0.50 mm | 44,475-44,49 mm | | | The reduced size of the crankpin 0.75 mm | 44,725-44,74 | | | The reduced size of the main journal 0.25mm | 49,227-49,242 mm | | | The reduced size of 0.50 mm radical neck | 49,477-49,492 mm | | | The reduced size of the main journal 0.75mm | 49,727-49,742 mm | | | Flywheel | Heartbeat | 0.1 mm | 0.13 mm | | Oil pump | The gap between the outer gear and the front cover | 0,12-0,18 mm | | | The gap between the internal gear and the front cover | 0,04-0,085 mm | | | The gap between the inner and outer gears | 0,06-0,11 mm | | | The oil pressure at idle | 147 kPa | | | The length of the spring of the safety valve in a free state | 46.6 mm | | | The length of the spring safety valve under load | 40.1 mm / 6.1 kg | | | Cooling system | The volume of coolant | 5.5 l | | | The cooling capacity of the radiator | 38,000 Kcal / h | | | Radiator cap | Overpressure valve | 81,4-108 kPa | | | Pressure reducing valve | -6.86 KPa | | Thermostat | the temperature of the beginning of opening | 82 ?� C | | | Temperature of full opening | 95 ?� C | | valve stroke | 8 mm | | The resistance of the coolant temperature sensor | 42,4-54,4 Ohm at 85 ?� C | | | 22,1-26,1 Ohm at 110 ?� C | | Coolant | Antifreeze | The content of the antifreeze coolant | | | Ethylene glycol | 50% | |
Tightening torques
| Nut and bolt the front support bracket | 45-55 | | Bolt front support | 70-90 | | Bolt back support | 70-90 | | Oil pressure sensor | 15-22 | | Cylinder head bolts | 35 + (90-92 ?�) + weaken +35 + (90-92 ?�) | | Bolts and nuts intake manifold | 18-25 | | Nuts of fastening of an inlet collector | 30-40 | | Bolts cylinder head cover | 8-10 | | Bolts camshaft cover | 12-14 | | Bolt backplate | 8-10 | | Union nut securing the connecting rod cap | 32-35 | | Cover bolts Bearing Crankshaft | 55-60 | | Flywheel bolts | 120-130 | | Bolt crankshaft pulley | 140-150 | | Bolt camshaft pulley | 80-100 | | Bolt tension roller of a gear belt | 20-27 | | Bolt guide roller of a gear belt | 43-55 | | Bolts toothed belt | 8-10 | | Bolts of the front cover | 20-27 | | Nut (large) securing the right support | 90-110 | | Nut (small) securing the right support | 50-65 | | Bolts and nuts of the right support to the cylinder block | 50-65 | | Nuts of fastening of gearbox support | 90-110 | | Side bracket bolts gearbox support | 30-40 | | Nut tree back support | 50-60 | | The nut bracket shaft back support | 30-40 | | Nut shaft front support | 45-60 | | Nut shaft front support bracket | 30-40 | | Oil filter | 12-16 | | Bolts of the oil pallet | 6-8 | | Oil drain plug | 35-45 | | Bolts of the oil filter | 15-22 | | Bolts and nuts bracket generator | 20-25 | | Bolt generator | 15-22 | | The mounting bracket bolts of the generator | 20-28 | | Bolts of fastening of the water pump pulley | 8-10 | | Bolts of fastening of the water pump | 12-15 | | Coolant temperature | 10-12 | | Coolant temperature | 15-20 | | Bolt coolant outlet | 17-20 | | Bolt Thermostat Housing | 15-20 | | Bolts air filter housing | 8-10 | | Bolts resonator | 4-6 | | Nuts and bolts intake manifold to the cylinder head | 15-20 | | Bolts of the air chamber to the cylinder block | 18-25 | | Bolts of the throttle assembly to the air chamber | 15-20 | | Mounting bolts of the exhaust manifold | 15-20 | | The oxygen sensor to the exhaust manifold | 50-60 | | Nuts of fastening of a reception exhaust pipe to the exhaust manifold | 30-40 | | Bracket bolts a reception exhaust pipe | 30-40 | | Bolts of the catalytic converter to the exhaust pipe of the receiving | 40-60 | | Nuts of fastening of the catalytic converter to the muffler | 30-40 |
|
