add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Touareg (from 2003 to 2006, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Touareg
Home
 
Volkswagen
Touareg
Operation and maintenance of car
Engine
Preliminary checks on the car
The mechanical part (petrol engines 3,2L)
The mechanical part (petrol engines 4,2L)
The mechanical part (diesel engines 5,0L)
Removing and installing subframe
Pressurization system (diesel engines)
Cooling system (petrol engines)
The cooling system (diesel engines)
Lubrication (petrol engines)
Lubrication system (diesel engines)
Injection System (petrol engines)
Fuel injection system (diesel engines)
Exhaust
FUEL (beninovye engines)
Replacement of the fuel filter
Pumping of fuel from the tank
Removing and installing fuel delivery unit, the fuel level sensor and ejection pumps
Check power pumps
Electronic control of engine power (electronic throttle actuator)
Activated charcoal filter (cars with the letter designation of the engine AZZ, BKJ, BMV, and BRJ)
Activated charcoal filter (cars with the letter designation of the engine BAA and BMX)
Tables
Transmission
Chassis
Steering Gear
Brakes
Onboard electric
Body
diagrams
 


Hit Counter by Digits


print page printable version

Pumping of fuel from the tank



The order of execution of works
Open the fuel filler hatch.

Installation devices for pumping fuel from the tank
Fig. 2.311. Installation devices for pumping fuel from the tank


Insert the bilge hose (Fig. 2.311) device for pumping fuel VAS 5190 by about 170-180 cm in the neck of the fuel tank and pump out the fuel.

NOTE
If the fuel is no longer pumped, the fuel tank is drained so that the flange of the sensor can be safely opened. With the remnants of the fuel tank can be removed.

If you want to work on the fuel pump and sensor, do the following:

Nuts of fastening of a cover
Fig. 2.309. Nuts of fastening of a cover


Cut the carpet from the point A to point B in the pre-notched site (Fig. 2.309).
Remove the nuts securing the cover 1. If necessary, remove the armrest support bracket 2 or the support bracket.
By the connection for fuel supply and fuel auxiliary heater enclose rags and disconnect the hose.

NOTE
To do this, click on the coupling.

Disconnect the connector of the fuel pump and the fuel level sensor.

Loosening of the retaining ring
Fig. 2.312. Loosening of the retaining ring


Remove the snap ring with a wrench T10202 from the flange of the sensor (Fig. 2.312).
Gently lift the sensor flange.
Insert the bilge hose device for pumping fuel VAS 5190 as far as possible to the right and left sides of the fuel tank and pump out the fuel.
When working on the left side of the tank, follow the guidelines above.

Tool for removing the vent pipes
Fig. 2.313. Tool for removing the vent pipes


When disconnecting the vent tube hose couplings button they can not be pressed. At the same time, use the assembly tool T10118 (Fig. 2.313).
In further work with the internal parts of the fuel tank sensor flange may be removed.
If it was only necessary to drain the fuel from the tank, it should re-install the sensor flange.
Before installation, check the O-rings in the flanges are tight.

NOTE
If the O-rings were swollen due to the impact of fuel, they must be replaced.


The direction of the installation flanges
Fig. 2.314. The direction of the installation flanges


Install the sensor flange with the locking plate in the direction of movement (Fig. 2.314).
Screw circlips right and left by a torque wrench T10202 145 Nm.




« previos page
Replacement of the fuel filter
next page »
Removing and installing fuel delivery unit, the fuel level sensor and ejection pumps

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.