printable version
Replacing bulbs
To replace the headlight bulbs, do the following. 1. Open the hood. 2. Disconnect the wire from the plug "minus" battery ... | | ... 3. Turn the headlight cover anticlockwise ... | 4. ... and remove the cover. |
NOTES Shown left headlight lamp replacement. Lamps in the right headlight are arranged symmetrically, replace them similarly. The cover is sealed with a rubber ring lights. Highly Compressed and tore the ring replaced. |
| | 5. Disconnect the headlight / headlight wiring harness connector. | 6. Bring spring clip hook on the reflector, Pull the lever, ... |
7. ... and remove the lamp head light.
A WARNING Do not touch the bulb as halogen lamp heats up and grease stains will cause darkening of the bulb. Take the bulb of the flask only clean gloves or a clean cloth. If the lamp is still left grease stains, remove them with alcohol. |
8. Insert the new lamp into the reflector and secure it with spring clip. | | 9. Pull the cartridge side light bulb from its socket (cartridge installed with little interference) and remove it from the lens unit. | 10. Remove the cartridge from the wedge base lamp. |
11. Insert the cartridge and install a new lamp cartridge into place. 12. Replace the cover lights. | | 13. Turn the bulb holder Indicator counterclockwise ... | 14. ... and remove it from the lens unit. |
15. Press the bulb, turn it counterclockwise and remove the cartridge. 16. Install the new lamp into the socket, and a cartridge in the lens unit.
To replace the lamp side indicator lamp, proceed as follows. 1. Disconnect a wire from the plug "minus" of the storage battery. | | 2. Slide back the turn signal housing ... | 3. ... and out of the wing. |
| | 4. Turn the chuck counterclockwise ... | 5. ... and out of the lantern of the index. |
6. Remove the bulb from the socket. 7. Insert a new bulb into the socket, and a cartridge in the case of the index. 8. Install the side turn signal lamp in the reverse order of removal.
To replace any bulbs in rear lamp cluster, do the following. 1. Disconnect a wire from the plug "minus" of the storage battery. 2. Open the trunk. | | 3. Squeeze the latches and open the luggage compartment in the lining for access to the lamp. | 4. Turn the bulb holder anti-clockwise ... |
| | 5. ... and out of the lantern. | 6. Press the bulb, turn it counterclockwise and remove the cartridge. |
7. When installing a new lamp tabs on the lamp should get into the slots on the cartridge. Then lock the lamp holder by turning it until it stops (90 ?�) clockwise. 8. Set the items in reverse order. 9. The remaining bulbs in rear lamp cluster is replaced by a similar manner.
To replace the lamp license plate light, proceed as follows. 1. Disconnect a wire from the plug "minus" of the storage battery. | | | 3. Remove the wedge base bulb from the socket. |
4. Install the new lamp. 5. Install the parts in reverse order of removal.
To replace the lamp in an additional stoplight, proceed as follows. 1. Disconnect a wire from the plug "minus" of the storage battery. | | 2. Turn the bulb holder an additional stoplight counterclockwise and remove it (the operation is carried out from the trunk). | 3. Press the bulb, turn it counterclockwise and remove the cartridge. |
4. Install parts in reverse order of removal.
NOTE One of the projections on the lamp holder has others. When installing orient the cartridge so that it coincided with a narrow slot (arrow), and rotate the cartridge clockwise until it stops. |
To replace the lamps in the room lamp, proceed as follows. 1. Disconnect a wire from the plug "minus" of the storage battery. | | 2. Press the screwdriver clamps and remove the ceiling diffuser. | 3. Press the spring contact and pull out the lamp. |
4. Insert a new lamp. | | 5. Set the first part of the front of the lens into the body the ceiling ... | 6. ... and press the back part until it clicks (snaps into place). |
To replace the light bulb in the ceiling of the luggage compartment, proceed as follows. 1. Disconnect a wire from the plug "minus" of the storage battery. | | 2. Overcoming the force lock, remove the bowl from the hole in the back of the vehicle (if necessary to pry with a screwdriver). | 3. Press the spring contact and pull out the lamp. |
4. Insert a new bulb in the ceiling. 5. Install the parts in reverse order of removal.
|