 printable version
Removal and installation of the control modules
general information Arrangement of control modules on board the vehicle Description of the procedures for removing and installing control modules injection (ME-SFI / CDI), AT (TCM / ETC), transfer case, braking and ancillary stabilization systems (ABS / BAS / EBV / ESP) is given in the Handbook (see chap. System supply and exhaust, Automatic Transmission, Transmission line and suspension and steering). The control module COMAND system with multi-function display (code ET4) Details of installation of the control module with the multifunctional COMAND display (1 of 2) Details of installation of the control module COMAND with multifunction display (2 of 2)
Control modules door assemblies The front door Details of installation of the control module front door
| - Turn on the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
|  | - Remove the interior door trim (see chap. Body).
- Disconnect the electrical wiring from the door control module (N69 / 1 or N69 / 2) (see. Section Disconnecting and reconnecting electrical mounting blocks and control modules).
- Remove the mounting screws (B) and remove the control module (N69 / 1 or N69 / 2).
- Installation is in the reverse order - the wiring modules, following the wires are not crossed, fix new bandages (C).
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
Backdoor Details of installation of the control module back door (1 of 2) Details of installation of the control module rear door (2 of 2)
| - Turn on the auxiliary battery and connect it to a standard battery and then disconnect the negative cable last.
| | - Remove the interior door trim (3) (see chap. Body).
- Disconnect the electrical wiring from the door control module (N69 / 3 or N69 / 4) (see. Section Disconnecting and reconnecting electrical mounting blocks and control modules).
- Clenching catches (1), remove the control module (N69 / 3 or N69 / 4).
- Installation is in the reverse order - the wiring modules, following the wires are not crossed, a new secure strapping (A).
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
Control module activation and the perception of the signal (SAM) / mounting fuse and relay Front module Details of the installation of the front module SAM / mounting fuse and relay box
The rear module Details of installation of the rear module SAM / mounting fuse and relay box (N10 / 2)
The control unit of the electronic ignition switch (EIS / EZS) Details of installation of the control module EIS / EZS | - On models corresponding complete set (code ET2) activate the service mode of the emergency call TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE).
| Turn on the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
| | - Remove the ignition key.
- Remove the lower left section of the instrument panel trim (see chap. Body).
- Squeeze the clips (1) and remove the module from the EIS (N73) drive cable (2) by pulling it in the direction of the arrow.
- Disconnect the connector (3) wiring module EIS (N73).
- Installation is in the reverse order - plug-in module EIS must be programmed in accordance with the included instructions.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
The control unit of telecommunications (codes ET7 / EV7) Details of installation of the control module of Telecommunications (codes ET7 / EV7)
| - Remove the center console (see chap. Body).
- Disconnect the connector (A) to connect the fiber optic cable to the control module (N112), - immediately close the connectors with protective caps waveguides.
- Clutching the locking tabs and gently pulling, disunite a socket (B).
- Remove the 2 mounting screws and releasing one nut, remove the bracket (1) control module (N112) from the tunnel transmission line.
- Remove the two spaced bottom fixing screws and remove the control module (N112) with the console panel (1).
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
The control unit of the emergency call TELE AID (code ET2) The models 463.250 / 323/333 Details of installation of the control module of the emergency call TELE AID models 463.250 / 323/333
The models 463.246 / 249 Details of installation of the control module of the emergency call TELE AID models 463.246 / 249 (1 of 3) Details of installation of the control module of the emergency call TELE AID models 463.246 / 249 (2 of 3) Details of installation of the console control unit of the emergency call TELE AID models 463.246 / 249 (3 of 3)  | | |
| - Lift the right front seat and slide it back until it stops.
- Release the two clamps (2) securing the front of the cover (1) control module.
- Slide the raised seat all the way forward, release the two rear retainer (arrow) and remove the cover (1).
- Give the two nuts (3) securing the rear of the control module (A35 / 8).
- Again, pull the raised seat in its rearmost position, give two front nuts (4) and remove the module (A35 / 8).
| Turn off the ignition, activate the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
| | - Remove the control unit (A35 / 8) from the support bracket.
- Unlock and disunite a socket (A35 / 8j10).
- Disconnect the fiber optic cable CAN bus and immediately stop the two halves of its connector (B) special that prevent light exposure, protective caps.
- Disconnect the connector (C) antenna cable.
- Remove the control unit of the emergency call TELE AID (A35 / 8).
- If necessary, release the front (6) and rear (7) nuts, separate from the console (5) wire (8) Bus CAN, free from penoizolyatsionnogo material (9) and disunite contact sockets - take care of the protection of the fiber optic waveguide caps and remove Console (5) module, threading wiring in through the window.
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor) and enter the required basic settings avionics.
|
|
Control Module protection sensor towing Details of installation of the control module (N27) protection sensor towing
| - On models corresponding complete set (code ET2) activate the service mode of the emergency call TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE).
- Disconnect the negative wire from the battery.
- Remove the center console (see chap. Body).
- Remove the rear module SAM (N10 / 2) - See above..
- Disconnect the electrical wiring from the control module (N27) protection sensor towing.
- Release the fasteners and remove the module (N27).
- Installation is in the reverse order - on the model of the corresponding configuration (code ET2) deactivate service mode of TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE).
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor) and enter the required basic settings avionics.
|
|
Control Module ultrasonic devices help when reversing (BA) (Code J44) Details of installation of the control module BA (1 of 2)
Details of installation of the control module BA (2 of 2)
| - Turn off the ignition, activate the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
| | - Releasing six catches (three on each side), remove equipped vetrootboynikom cover (A) luggage.
- Remove the support bracket (B) on the left wall vetrootboynika luggage.
- On models corresponding complete set (code V53) Remove the left glovebox.
- On models corresponding complete set remove the TV-tuner (A2 / 42), - code EM9 and CD-changer (A2 / 6) - ER5 code (see. Section Removal and installation CD-changer / TV-tuner).
- Give fixing nuts (3) Disconnect the connector (X26 / 26 and 4) and remove the control module BA (N62).
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
The control unit for seat heating (code H11) Details of installation of the control unit for seat heating (code H11)  | | |
| - On models corresponding complete set (code ET2) activate the service mode of the emergency call TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE).
- Disconnect the negative wire from the battery.
- Releasing six catches (three on each side), remove equipped vetrootboynikom cover (A) luggage.
- Remove the support bracket (B) on the left wall vetrootboynika luggage.
- On models corresponding complete set (code V53) Remove the left glovebox.
- On models corresponding complete set remove the TV-tuner (A2 / 42), - code EM9 and CD-changer (A2 / 6) - ER5 code (see. Section Removal and installation CD-changer / TV-tuner).
- Give fixing nuts (1) Disconnect the connector (3) and remove the control module (N25 / 6).
- Installation is in the reverse order - on the model of the corresponding configuration (code ET2) deactivate service mode of TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE).
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor) and enter the required basic settings avionics.
|
|
Control module voice commands Linguatronic (codes EL1 ÷ EL6) Details of installation of the control module of Linguatronic
| - Turn off the ignition, activate the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
| | - Bend the panel carpet in the driver's footswitch well.
- If necessary lift finishing panel (4) and release nut (1).
- Remove the control module Linguatronic (A35 / 11), complete with support bracket (2).
- Release and disunite sockets (5 and 6), - immediately stop the input waveguide fiber cable D2V special plugs.
- Give fixing nuts (3) and remove the control module (A35 / 11).
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
Amplifier audio control module (code E66) Details of installation of the control module audio amplifier
| - Slide the raised driver's seat forward until it stops.
| - Turn off the ignition, activate the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last.
| | - Disconnect the connector (1).
- Give nuts (2) and remove the bracket (3) with the attached amplifier (N40 / 9).
- Remove the mounting screws (4) and remove the amplifier (N40 / 9) from the console (3).
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
SRS control module Model release of 30.11.01 Details of installation of the module of management SRS models of manufacture 30.11.01
| - Disconnect the negative wire from the battery.
- Remove the center console (see chap. Body).
- Disconnect from the control unit (N2 / 2) wiring, - try to remember the wiring diagram weight (W26)
- Remove the screws and remove the module (N2 / 2).
- Installation is in the reverse order - marked with an arrow on the housing module installed must point forward while moving.
- Finally, make a program data input SRS.
|
|
Models of release since 01/12/01 Details of installation of the module of management SRS (N2 / 2) on models with the release of 01.12.01
| - Remove the control unit from the towing protection devices (see. Above).
- Disconnect the electrical wiring, release fasteners, and remove the control module SRS (N2 / 2), - try to remember the wiring diagram weight (W26).
- Installation is in the reverse order.
- Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).
|
|
|
