| 1. Turn off the appropriate lamp. |
| Spotlight |
| 2. Open the bonnet. |
| 3. If necessary, replace the lamp lights left: Unscrew the enclosure and remove the battery. |
| 4. Remove the plug on the rear side of the headlamp. |
| 5. Remove the rubber cap on the rear side lights. |
 | 6. Squeeze the spring clip (1) bulb holder and fold down. |
| 7. Remove the faulty lamp. |
| 8. Do not touch the bulb of the new lamp. Set the lamp so that the tip into the corresponding recesses of the housing. Average tab on the lamp cap should be at the top. |
| 9. Raise the spring clamp, compress and secure. |
 | 10. Attach the rubber cap on the rear side lights, thrusting tongues cutouts. Push the plug on the rim. |
| 11. If removed, install and secure the battery enclosure. |
| 12. Check headlight adjustment to the service station. |
| Parking lights front |
| 13. The lamp is in the parking light reflector headlights. Turn the lamp socket for the left and pull back from the reflector. The connection cable to the socket can not be removed. |
| 14. Drown lamp rim, turn left and take out. |
| 15. Insert the new bulb, turn clockwise and secure. |
| 16. Insert rim of the lamp reflector and turn fully to the right. |
| The front turn signal |
| 17. Open the bonnet. |
| 18. Insert a screwdriver between the top of the headlamp and the turn signal housing. Locking tab otognetsya side. |
 | 19. Lower the screwdriver forward in the direction of the arrow, removing thus the housing Indicator forward. |
| 20. Remove the front turn signal assembly. |
| 21. Turn left lamp frame and removed from the body. |
 | 22. Drown little lamp in the frame rotated 90 ?� (1/4 turn) to the left and remove. |
| 23. Install the new lamp, slightly to press and turn right. |
| 24. Insert the frame into the housing indicators (turn clockwise until it stops). |
| 25. Insert the flashlight pointer guides (top and bottom), press until the locking tab clicks. |
| Anti-fog headlight |
| 26. Unscrew the protective cover on the left side of the rear fog lamp (under the bumper). |
| 27. Remove the spring clip of the lamp, take out the bulb. |
| 28. Install the new lamp so that the spouts into the corresponding recesses of the housing. |
| 29. Fit and secure the spring clip. |
| 30. Screw the protective cap. |
| 31. Check the adjustment of the fog lamps in the workshop. |
| Rear lights |
| 32. Open the trunk lid. |
| 33. Grasp the part of the trunk of the two lamp unit retaining language squeeze them together and remove the unit inside. |
 | 34. Drown defective bulb, turn left 45 ?� and remove. |
| 35. Drown new lamp into the rim, turn right and secure. |
| 36. Insert the lamp in the housing unit, the tabs must engage. |
| Rear fog light |
 | 37. Press the stop tab fog lights (arrow) and remove the lens. |
| 38. Remove the lamp housing. |
| 39. Turn left rim faulty bulb and remove. |
| 40. To unscrew the lamp from the left rim and replace. |
| 41. Install the left side of the lens lights up and drown until the locking tab clicks. |
| License Plate Light |
 | 42. Lanterns license plate fixed with 2 screws each (arrows). Unscrew the Phillips screwdriver diffuser. |
| 43. Remove the license plate light. |
| 44. Remove the rim of the lamp. |
| 45. Drown little lamp in the frame, turn left on 90 ?� (1/4 turn) and remove. |
| 46. Install the new lamp, slightly to drown and turn right. |
| 47. Install the lamp. |
| 48. Install the diffuser and screw is not strong. Turn off the appropriate lamp. |
| Replacing the lamp on the ceiling of the car |
| 49. Take out the night light for the side opposite the switch. |
| 50. Turn the frame on the back side of the lamp 90 ?� {1/4 turn) to the left and take out the bulb. Install the new lamp. |
| 51. Remove the lens and replace the lamp assembly as defined. If the lamp is sitting loosely, bend contacts. |
| 52. Install the lamp in the ceiling cutout. |
| Courtesy lamps and lighting trunk |
| 53. Insert a narrow screwdriver into the side cut of the lens (the side opposite the switch) and remove the lamp. |
| 54. Replace the lamp assembly as defined. If the lamp is sitting loosely, slightly bend contacts. |
| 55. Insert the first side to the light switch, then insert the other side. |
| 56. Compress and remove the lens. |
| 57. Drown lamp gently into the rim, turn left on 90 ?� (1/4 turn) and remove. |
| 58. Install the new lamp, slightly to drown and turn right. |
| 59. Install the lens and secure. |
