add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Chevrolet Lanos (since 2004 of release), Daewoo Lanos (since 1997 of release)

general info. full specifications. diagnostics. hints. tips. tricks
Chevrolet Lanos
Home
 
Chevrolet
Lanos
Device Car
Operating Guidelines
Faults in the way
Maintenance
Engine
Transmission
Chassis
A steering
The brake system
Electrical
Body
Design Features
Possible malfunctions of the body, their causes and remedies
Removing, dismantling and installation of bumpers
Removing and installing radiator grille
Removal and installation of mudguards of wheels and Lockers
Removal and installation of a forward wing
Removal and installation of a lattice box vozduhopritoka
Hood
Door
The trunk lid
Manhole cover fuel tank filler pipe
Seats
Removal and installation of facing of a tunnel floor
Restraint System (SRS)
Rear view mirrors
Dashboard
Heater and air conditioning
Interior fittings
Removal and installation of facing of salon
Removal and installation of facing the boot
Windscreen wiper
Replacement of the fixed glass body
Removing and installing the attachment flanges of the battery
Care body
Wheels and tires
Purchase of spare parts
A trip to the STO
Winter car operation
Preparation for technical inspection
Tips novice mechanic
Applications
Diagrams
 


Hit Counter by Digits


print page printable version

Removal and installation of facing of salon



You will need: a screwdriver with a flat blade and Phillips.

NOTE
Showing removal and installation of facing the left side of the cabin. Lining the right side is removed similarly.

1. Before removing the stand facing the wind window, remove the rack from the edge of the door frame seal, as it covers the edge of the lining.
2. Remove the windscreen pillar trim, overcoming the resistance of the caps of its fastening.

NOTE
Inspect the pistons facing mounting. Broken replace caps.

3. Remove the bracket facing the front side wall ...
4. ... and remove the trim.
5. To remove the front facing the threshold, pulling it up, remove the bracket caps of its fastening and then removing the spring clips mounted in the grooves facing with folding threshold, remove the trim.



NOTE
The front end of the front facing of the threshold set under the rear edge of the front quarter panel trim. If the removal of the front facing difficult threshold, remove the bracket facing sidewall (see. P. 3) to release the sill trim.

6. To remove the rear sill lining Remove the screw securing it to the base of the body ...
7. ... and pulling it up, remove the bracket caps of its fastening. Then, by removing the spring clips mounted in the grooves facing with folding threshold, remove the trim.
8. Before removing the lower part of the B-pillar trim, remove the front and rear sill lining (see. Nos. 5 and 7). Then, a little bent edge of the lower part of the B-pillar trim, remove them from the rack otbortovok ...

9. ... and remove the lower part of the liner.
10. Before you remove the upper part of the B-pillar trim, remove the lower part of the liner (see. P. 9), remove the two screws fastening the seat belt and disconnect from the upper B-pillar seat belt anchor (see. Nos. 3 and 6, "Replacing the front belt" ). Then, pull the rack from the bottom edge of the upper part of the lining ...

11. ... having hooked a screw-driver, output its top edge from the ceiling trim and remove the upper part of the lining.
12. Before removing the tailgate lining the shelves, remove the rear seat back (see. "Removing and installing rear seat") ...
13. ... and in the trunk, disconnect the harness connector of an additional stoplight.

NOTE
Lining is attached to a back shelf with six pistons.

14. Remove the three pistons of the front ...
15. ... and the top fastening lining the shelves of a back ...
16. ... and remove the liner assembly with additional stop sign.
17. If necessary, remove the brake lining signal by removing the two nuts securing it (see. "Replacement of an additional stoplight").
18. Remove the trim from the rear of the rack, overcoming the resistance of percussion caps of its fastening.

NOTE
Inspect the pistons facing mounting. Broken replace caps.

19. Remove the upper and lower seat belt mounting (see. "Replacing the back seat belt").
20. Pushing force clamps, remove the hole facing edging holes.
21. Skip edging hole with the hole in the belt buckle facing ...
22. ... and remove the trim from the seat belt.
23. Before removing the rear quarter panel trim, remove the rear sill trim (see. Nos. 6 and 7 in this section), the C-pillar trim (see. Pp. 18-22 in this subsection), and the passenger side seat belt in the rear seat (see. "Replacing the rear seat belt").
24. Remove the two pistons mount rear quarter panel trim on the body ...
25. ... and remove the trim.
26. Install the liner interior and all the removed parts in reverse order of removal.




« previos page
Replacing the sun visors
next page »
Removal and installation of facing the boot

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.