REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Hyundai
	Accent
		Instructions
		Engine
			Engines SOHC
				Technical data
				Toothed belt
				Check toothed belt tension
				Adjusting the tension of the toothed belt
				Ribbed Belts
				Engine Supports
				The front cover and the oil pump
				Air filter (ACL)
				Cylinder head
				Rocker
				Hydraulic jacks of backlashes of valves
				Replacing the valve seat
				Replacing the valve guide
				Valve
				Camshaft
				Cranks
				Crankshaft
				Flywheel
				The piston pin
				An exhaust manifold
				Intake manifold and the air chamber
				Cylinder block
				Removing and installing engine and gearbox
				Exhaust
				Troubleshooting
			Engines DOHC
		Greasing system
		Cooling
		Control, reduced toxicity
		Fuel system
		Ignition system
		Coupling
		Transmission
		Axes and power shafts
		Suspension
		Steering
		Brakes
		Body
		Air
		Electrical equipment
		Appendix
		Wiring

printable version

Camshaft

1 - a bolt, 80-100 N ??? m;
2 - washer;

3 - dowel pin;
4 - camshaft.

Withdrawal

PERFORMANCE ORDER

1. Remove the crankcase ventilation hose.

2. Remove the water pump pulley and the crankshaft.

3. Remove the cover of a gear belt.

4. Take the tension roller of a gear belt to the water pump and temporarily secure it in this position.

5. Remove a gear belt from a camshaft pulley.

6. Remove the camshaft pulley.

7. Remove the camshaft pulley.

8. Remove the cylinder head cover.

9. Remove the rocker shaft assembly.

10. Remove the camshaft bearing cap.

11. Remove camshaft.

Check

PERFORMANCE ORDER

1. Check the camshaft to the absence of uneven wear, cracks or damage.
	2. The two points to measure the height of each cam of the camshaft. The nominal height of the cams of the inlet camshaft: 42.8575 mm The nominal height of the exhaust camshaft: 42.7354 mm Minimum permissible height of the cams of the inlet camshaft: 42.3575 mm Minimum permissible height of the exhaust camshaft: 42.2353 mm
3. Check the surface of the cam to the absence of uneven wear and damage.
4. Check each bearing damage. If the working surface of the bearing excessively damaged, replace the cylinder head or the camshaft bearing cap.

Forward sealing ring of a camshaft

PERFORMANCE ORDER

1. Check the sealing lips of the sealing ring for wear. If the working edge is worn or damaged, replace the O-ring.

2. Check the surface of the camshaft contact with the sealing ring. If the surface is uniformly worn, replace the camshaft.

Axial backlash of a camshaft: 0,07-0,28 mm.

Setting

PERFORMANCE ORDER

	1. Before installation, apply a thin coat of clean engine oil to all sliding surfaces of the camshaft. Install the camshaft.
2. Install the camshaft bearing caps.
	3. Install the ignition coil.
4. Install the rocker arm shaft and rocker.
5. Apply engine oil working edges and an outer surface of the sealing ring and a special tool set 09221-21000 O-ring on the front of the camshaft. Hammer blows on specially adapted set O-ring all the way into the slot.
6. Install the camshaft pulley and fix its bolt. Torque: 80-100 N ??? m
7. the mark on the camshaft and mounting the crankshaft pulley mark pointer, the piston of 1st cylinder will be in the TDC on the compression stroke.
8. Place the gasket into the recess of the cylinder head cover.
9. Temporarily install the cylinder head cover.
10. Start up the engine and leave it to the engine speed to idle.
11. Tighten the cover bolts to torque. Torque: 8-10 N ??? m
12. Replace the timing belt covers.
13. Install the water pump pulley and the crankshaft pulley.

« previos page
Valve

next page »
Cranks