 printable version
Technical data
Technical data Data | Value | | Clutch | Hydraulic | | The diameter of the friction lining (external x internal) | 215h145 mm | | The inner diameter of the main cylinder | 20.64 mm | | The inner diameter of the cylinder | 15.87 mm | | Thickness of the clutch disc | 8,5 ?� 0,3 | | Free travel | 6-13 mm | | The clutch pedal | 145 mm | | The height of the clutch pedal | 166.9 mm | | Minimum distance to heads of rivets at the limit of wear clutch facings | 1.1 mm | | The difference between the height of the ends of the diaphragm spring | 0.5 mm | | The clearance between the piston and the clutch slave cylinder | 0.15 mm | | The clearance between the piston and the clutch master cylinder | 0.15 mm |
Recommended lubrication Elements | Grease | | The contact surface of release bearing and clutch release bearings | CASMOLY L 9508 | | The inner surface of release bearing | CASMOLY L 9508 | | The inner surface of the clutch cylinder, the piston and sleeve | Brake fluid DOT 3 or DOT 4 | | Slots clutch | CASMOLY L 9508 | | The inner surface of the clutch master cylinder, the piston and sleeve | Brake fluid DOT 3 or DOT 4 | | Pusher clutch master cylinder | SAE J310a, NLGI ?��2 | | The shaft and the clutch pedal bushing | J310a, NLGI ?��1 | | Clutch fork | CASMOLY L 9508 | | Slots a primary shaft of a transmission | CASMOLY L 9508 |
Tightening torques, N ??? m Data | Value | | Bracket clutch pedal | 19-28 | | Prop the clutch pedal to the master cylinder | 8-10 | | The connecting pipe coupling nuts | 13-17 | | Bracket pipe coupling | 4-6 | | Bondage expansion tank | 13-17 | | The cylinder clutch | 15-22 | | Bolt cylinder clutch | 20-25 | | The casing with the pressure plate | 15-22 |
general information The clutch located between the engine and the transmission and intended for separation and connection of the flywheel disposed on the crankshaft of the engine and a primary shaft of the gearbox. Clutch consists of a conducted (frictional) disk, a casing of coupling with a press disk and diaphragm spring and clutch mechanism. The friction disc consists of two annular friction linings, which are mounted on the hub via the damper spring. Diaphragm spring mechanism creates a force that integrates the work of the flywheel and the pressure of the driven disc for joint rotation, in this case, the clutch is turned on and transfers torque from the engine to the transmission. Management is carried out clutch pedal clutch. Clutch follows. By pressing on the clutch pedal moves the piston in the master cylinder, compressing the fluid whose pressure is transmitted through the hose to the clutch slave cylinder, the piston which in turn acts on the clutch release fork. Clutch fork moves the clutch, which presses the center of the diaphragm spring, thus relieving stress inclusion on the perimeter of the spring and the pressure plate moves back. This releases the clutch disc, after which the motor shaft and the transmission shaft can rotate independently of each other. On both sides of the slave disk attached friction linings. The leading portion of the disk is connected to the hub through the details of the torsional vibration damper, which provides a resilient connection between them. Vibration damper reduces the dynamic loads that cause twisting (unwinding) shafts transmissions that occur during a sudden change in the vehicle speed, running over bumps in the road, with a sharp turn on the clutch, and also due to non-uniformity of torque. Elastic vibrations transmission parts cause noise in machinery and aggregates, as well as vibration, resulting in possible damage to the parts, if the amplitude of elastic vibrations reach considerable values. In order to absorb the energy of elastic torsional vibration damper is used.
|
