printable version

Electricity supply electrical trailer

general information

Available in several types farkopnyh connectors with a different arrangement of terminals in them. The most common is a 7-pin connector, which provides the formation of two additional circuits normally used to power the reversing lamps and electric trailer brakes.

When equipment tow bar may have to replace the former Flasher turns more powerful with the aim of maintaining agreed in adopted in a particular region SDA frequency of flashing signal lights. The authorities of some regions also require the mandatory installation of the instrument panel control indicator lights.

If the receptacle connector farkopnogo does not meet on a standard size installed on the trailer connector, you must purchase one of the appropriate transitional manufactured nozzles (see. Accompanying illustration).

1 - for the docking connector type Brylite jack type Utilux 2 - for snapping 6-pin type Utilux to 5-pin type Utilux

Installing the connector farkopnogo

For equipment hitch receptacle connector farkopnogo required (at a minimum): a corresponding receptacle connector of the trailer, the support bracket, 7-wire flexible cable, insulated connectors for connecting wires and rubber grommet.

The necessary components for power supply equipment trailer with farkopnogo connector type Utilux.

1 - plug 2 - Terminal Blocks 3 - Bellow 4 - Bellow 5 - the screws 6 - slot 7 - connector for connecting wires	8 - wire 9 - grommets, 10 - 7 - core flexible cable 11 - control Repeater 12 - the screw 13 - support bracket 14 - Lamp

PERFORMANCE ORDER

Disconnect the negative wire from the battery. Locate the wiring harness lamps at the rear of the vehicle. Locate the power wires left and right rear turn indicators, rear position lamps, stop lamps, reversing lamps and weight. Using the wiring diagram given at the end of this Chapter, determine the color coding of each of these wires. Using insulated connectors connect the 7-wire flexible cable for each of the found wire. In the case of farkopnogo connector 7-pin type stick to the following standard color coding scheme: Terminal number Circuit Colour 1 Lamp indicator left turn Yellow 2 Reversing lamp fire Black 3 Mass White 4 The lamp indicator of the right turn Green 5 Electric brakes Blue 6 Lamp stoplight Red 7 Lamp side light Brown In the case of farkopnogo connector 6-pin type stick to the following standard color coding scheme: Terminal number Circuit Colour 1 Lamp side light Brown 2 Lamp indicator left turn Yellow 3 The lamp indicator of the right turn Green 4 Lamp stoplight Red 5 Auxiliary circuit Blue 6 Mass White In the case of farkopnogo connector 5-pin type stick to the following standard color coding scheme: Terminal number Circuit Colour 1 Lamp indicator left turn Yellow 2 Mass White 3 The lamp indicator of the right turn Green 4 Lamp stoplight Red 5 Lamp side light Brown Drill into the floor panel of a vehicle suitable hole and insert the rubber grommet. Before you drill the hole, check whether it is possible to use any of the existing technology. Grommet must be installed without fail to avoid rubbing wires. Insert into the hole with the installed grommet 7-pin flexible cable. Cut the cable to length and put it bellow. Strip each of the cable cores of insulation about 15 mm. Connect the wires to the terminals of the receptacle, following the standard color scheme and following the manufacturer's instructions connector. Assemble the socket and replace the rear end of his boot. Components 7-pin connector type Brylite farkopnogo shown in the accompanying illustration. 1 - 7 - core flexible cable 2 - Cover 3 - slot 4 - Bellow 5 - plug 6 - screws Install the support bracket as close to the hitch ball stud and high enough to keep the ground clearance of the vehicle. Set in the bracket receptacle connector. Connect the plug of the trailer to the tow bar receptacle to test the health of their connections.

Install the trailer connector

For equipment trailer plug connector farkopnogo required (at a minimum): a corresponding receptacle connector car connector, 7-pin floppy cable and insulated connectors for wiring.

To insert the plug on the trailer is similar to that for mounting receptacle connector on the vehicle, taking into account the following points.