REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Hyundai
	Accent
		Instructions
		Engine
		Greasing system
		Cooling
		Control, reduced toxicity
		Fuel system
		Ignition system
		Coupling
		Transmission
		Axes and power shafts
		Suspension
		Steering
			Technical data
			The mechanism of the tilt steering column
			Steering transfer without power steering
			Tie Rod
			Check backlash steering wheel for vehicles with power steering
			Checking steering angle of front wheels
			Check torque pin of the spherical rod end
			Check of effort of the steering wheel for vehicles with power steering
			Checking the steering wheel return to its original position
			Check the fluid level
			Liquid replacement in a hydraulic drive the power steering
			Bleeding the hydraulic system of the power steering
			Checking the belt drive power steering pump
			Checking the fluid pressure in the hydraulic system
			Steering transfer of cars with power steering
			The power steering hoses
			Power steering pump
			Troubleshooting (steering without the amplifier)
			Troubleshooting (power steering)
		Brakes
		Body
		Air
		Electrical equipment
		Appendix
		Wiring

printable version

Power steering pump

1 - a bolt, 55-60 N ??? m;
2 - O-ring;
3 - a bolt, 16 N ??? m;
4 - suction pipe;
5 - the gauge of pressure of the fluid;
6 - a pulley;
7 - a lock ring;
8 - Spacing sleeve;
9 - shaft bearings;
10 - a sealing ring;
11 -korpus;

12 - a spring;
13 - inner sealing ring;
14 - outer sealing ring;
15 - front side plate;
16 - blades;
17 - a rotor;
18 - pin;
19 - cam ring;
20 - a lining;
21 - Back Cover;
22 - a bolt, 38 N ??? m.

Withdrawal

A warning

When servicing the oil pump, close the generator a polyethylene film.

PERFORMANCE ORDER

1. Disconnect the pressure hose from the pump.
	2. Remove the suction strainer from the connector suction and drain the liquid in the container.
3. Loosen the bolts and remove the pump drive belt.
4. Remove the mounting bracket bolts of the pump and disconnect the pressure sensor connector.
5. Remove the pump.

Dismantling

PERFORMANCE ORDER

	1. Remove the suction pipe and the O-ring from the pump.
2. Remove the back cover with gasket and studs.
3. Remove the stator ring.
4. Remove the rotor and blades.
	5. Remove the front side plate.
6. Remove the inner and outer sealing ring.
7. Remove the spring.
	A warning When assembling it is necessary to use a new gasket and O-ring.
8. Remove the pulley nut and remove the spring washer.
	9. Remove the pulley and the woodruff key.
10. Using special pliers, remove the retaining ring.
	11. Squeeze pulley shaft bearing. If necessary, use a nylon hammer.
12. Remove O-ring from the pump housing.
	A warning When assembling the need to use a new sealing ring.
13. Remove the bracket guide and remove the nut.
14. Disconnect from the pump housing and remove the throttle and spring.
15. Remove the seal ring from the socket.
	A warning Do not disassemble the throttle.

Check

PERFORMANCE ORDER

1. Clean all pump parts with an appropriate solvent.

2. If there are any damaged parts of the pump, replace the pump assembly.

3. If the pulley is damaged or deformed, replace it.

4. If there is fluid leakage around the O-ring, replace it.

5. If damaged or worn, or pulley shaft splines, replace the affected parts.

Assembly

PERFORMANCE ORDER

1. Turn the pump.
2. Establish a spring throttle valve and plug in the pump casing.
A warning Grease with a thin layer of liquid ATF DEXRON II All replaced parts, including the oil seal and O-ring.
3. Install the bracket guide and screw the nut.
	4. The special tool 09222-32100 install oil seal in the pump housing.
5. Gently insert the assembly of the shaft and install the snap ring.
	6. Install the pump pulley with the woodruff key.
7. Install the spring and the inner and outer sealing ring.
	8. Install the front side plate.
	9. Insert the pins into the recesses of the front housing, then install the cam ring, paying attention to the direction of installation.
10. Set the rotor so that the marks on the rotor located on the side opposite the front of the housing.
	11. Install the blade rounded part outwards.
12. Install the gasket and the rear cover.
13. Tighten the suction connector.

Setting

PERFORMANCE ORDER

1. Place the pump in the pump bracket.

2. Place the suction filter.

3. Install the V-ribbed belt and adjust its tension.

4. Connect the pressure hose to the pump and the suction filter tank.

A warning

Set the hoses so that they are not twisted and not come into contact with any other parts.

5. Pour the liquid.

Recommended fluid: PSF-3

6. Bleed the hydraulic power steering.

7. Check the pressure created by the pump.

« previos page
The power steering hoses

next page »
Troubleshooting (steering without the amplifier)