add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Elantra (from 2000 to 2004, the year of issue)
general info. full specifications. diagnostics. hints. tips. tricks
 Hyundai Elantra
Home
 
Hyundai
Elantra
Gasoline engines 1.6, 1.8 and 2.0 liters
The diesel engine of 2.0 liters
Greasing system
Cooling
Fuel system
Control systems and emission control
Ignition system
The system of preliminary heating of the diesel engine
Coupling
Manual transmission
Automatic Transmission
Technical data
Check the fluid level in automatic transmission
Substitution fluid in an automatic transmission
Check conduction switch the transmission range (F4A42)
Switch the transmission range and adjustment of the control cable (F4A42)
Check the operation of the selector lever (A4AF3)
Adjustment of the switch indicate the position of the selector lever (A4AF3)
Component testing of an automatic transmission (F4A42)
Testing of teamwork of an automatic transmission and the engine for the motionless car (F4A42)
Check the transmission fluid pressure (F4A42)
Check the transmission fluid pressure (A4AF3)
The diagnostic function
Diagnostic codes
Adjustment of an axial backlash reaction brake (F4A42)
Adjusting the axial clearance of the brake of the second transmission (F4A42)
Adjusting the axial clearance of the brake transmission and low reverse gear (F4A42)
Adjusting the axial clearance of the sun gear downshift (F4A42)
Adjusting the preload of the differential (F4A42)
Elements of hydraulic control system
Identification of bearing automatic transmission F4A42
The control lamp fault (MIL)
Identification of bearing automatic transmission F4A43
Adjusting the servo compulsory inclusion downshift (A4AF3)
Adjust the line pressure (A4AF3)
Replacement of an oil sealing ring of a power shaft
Removing and installing transmission F4A42
Removing and installing transmission A4AF3
Control automatic transmission
Installing the locking device
Installing a locking key
Drive shafts, front and rear axles
Suspension
Steering
Brakes
Body
The air conditioning system
Electrical equipment
Electrical diagrams
 


Hit Counter by Digits


print page printable version

Removing and installing transmission A4AF3



Withdrawal

PERFORMANCE ORDER

  1. Remove the drain plug and drain into a suitable container gear oil from the gearbox.
  1. Remove the air filter.
  1. Disconnect the connector from the transmission range switch.
  1. Remove the solenoid connector and the connector from the oil temperature sensor.
  1. Remove the control cable.
  1. Remove the control cable clamp.
  1. Disconnect the hose from the oil cooler.
  1. Disconnect the connector from the speedometer.
  1. Remove the front wheels.
  1. Remove the starter.
  1. Remove the upper bolts gearbox.
  1. Remove the caliper front brakes.
  1. Disconnect from the knuckle ball rod end.
  1. Remove the speed sensor and remove the screws A-pillar to the steering knuckle.
  1. Remove the drive shaft and remove the nut on the left-hand nave.
  1. Special adaptation support the engine so that the engine weight was perceived device.
  1. Remove the transmission bracket.
    1. Remove the bolt support.

b. Turn (left) a bolt from the body.

c. Remove (upper) bolt from the body.

  1. Remove the front roll stopper from the bottom of the frame.
  1. Remove the rear roll stopper from the bottom of the frame.
  1. Remove the cover from the housing socket.
  1. Remove the bolts and remove the plate covering the torque converter.
  1. Remove the plate bolts to the engine block.
  1. Establish a jack under the bottom frame.
  1. Remove the lower bolts gearbox.
  1. Remove the front muffler.
  1. Remove the bolts of the lower frame.
  1. Establish a jack under the gearbox.
  1. Remove the lower bolts gearbox.
  1. Remove the gearbox.

Setting

PERFORMANCE ORDER

  1. Replace the front part of the transmission torque converter and set the transmission to the engine.

If the converter is first set to the motor when setting the gearbox may be damaged O-ring transmission.

  1. Install the transmission control cable and adjust as follows.
    1. Move the selector lever and the transmission range switch in position N and install the control cable transmission.
    2. When connecting the control cable mounting bracket to the transmission, select the clip so that it came into contact with the cable management.
    3. Adjusting nut, select any free wheeling in the control cable and check that the selector lever moves smoothly.
    4. Check that the control cable is properly adjusted.




« previos page
Removing and installing transmission F4A42		 next page »
Control automatic transmission

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.