add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Elantra (from 2000 to 2004, the year of issue)
general info. full specifications. diagnostics. hints. tips. tricks
 Hyundai Elantra
Home
 
Hyundai
Elantra
Gasoline engines 1.6, 1.8 and 2.0 liters
The diesel engine of 2.0 liters
Greasing system
Cooling
Fuel system
Control systems and emission control
Ignition system
The system of preliminary heating of the diesel engine
Coupling
Manual transmission
Automatic Transmission
Technical data
Check the fluid level in automatic transmission
Substitution fluid in an automatic transmission
Check conduction switch the transmission range (F4A42)
Switch the transmission range and adjustment of the control cable (F4A42)
Check the operation of the selector lever (A4AF3)
Adjustment of the switch indicate the position of the selector lever (A4AF3)
Component testing of an automatic transmission (F4A42)
Testing of teamwork of an automatic transmission and the engine for the motionless car (F4A42)
Check the transmission fluid pressure (F4A42)
Check the transmission fluid pressure (A4AF3)
The diagnostic function
Diagnostic codes
Adjustment of an axial backlash reaction brake (F4A42)
Adjusting the axial clearance of the brake of the second transmission (F4A42)
Adjusting the axial clearance of the brake transmission and low reverse gear (F4A42)
Adjusting the axial clearance of the sun gear downshift (F4A42)
Adjusting the preload of the differential (F4A42)
Elements of hydraulic control system
Identification of bearing automatic transmission F4A42
The control lamp fault (MIL)
Identification of bearing automatic transmission F4A43
Adjusting the servo compulsory inclusion downshift (A4AF3)
Adjust the line pressure (A4AF3)
Replacement of an oil sealing ring of a power shaft
Removing and installing transmission F4A42
Removing and installing transmission A4AF3
Control automatic transmission
Installing the locking device
Installing a locking key
Drive shafts, front and rear axles
Suspension
Steering
Brakes
Body
The air conditioning system
Electrical equipment
Electrical diagrams
 


Hit Counter by Digits


print page printable version

Removing and installing transmission F4A42



Withdrawal

PERFORMANCE ORDER

  1. Disconnect in the first place, the wire from the negative terminal of the battery, and then - on the positive. Remove the battery and battery support.
  1. Remove the drain plug and drain into a suitable container gear oil from the gearbox.
  1. Remove the air filter.
  2. Disconnect the connector from the speedometer.
  1. Disconnect the connector from the transmission range switch, solenoid connector and the connector from the oil temperature sensor.
  1. Disconnect the hose from the oil cooler.
  1. Remove the control cable.
  1. Remove the universal joint shaft of the steering column of the steering gear.

Mark the position of the universal joint shaft of the steering column and the steering gear shaft.

  1. Disconnect the hose from the power steering pump.
  1. Disconnect the return hose from the oil pump power steering.
  1. Remove the upper bolts gearbox.
  1. Special adaptation J28467-B, J28467-125 support the engine so that the engine weight was perceived device.
  1. Remove the front wheels and brake calipers front.
  1. Disconnect from the knuckle ball rod end.
  1. Remove the speed sensor and remove the screws A-pillar to the steering knuckle.
  1. Remove the transmission bracket.
    1. Remove the bolt support.

b. Remove (upper) bolt from the body.

c. Remove the (side) bolt from the body.

d. Remove the side of the mounting bolt gearbox.

  1. Remove the front roll stopper.
    1. Remove the bolt support.

b. Remove (upper) bolt retainer.

c. Remove the (lower) fastening bolt retainer.

  1. Remove the rear roll stopper.
    1. Remove the bolt support.

b. Remove the bolt retainer.

  1. Remove the drive shaft.
  1. Remove the screws and remove the lower frame.
  1. Support gearbox jack.
  1. Remove the lower bolts gearbox.
  1. Remove the bolts the gearbox to the engine.
  2. Remove the transmission from the car.

  1. Supports the engine and transmission to be installed in its place without tension.
  2. The sequence of installation brackets.
    1) Bracket engine mounting.
    2) Upper bracket gearbox.
    3) Mount the rear support.
    4) the front support bracket.
  3. When installing the front support bracket being careful not to damage the bearing, which can lead to excessive vibration.

Setting

PERFORMANCE ORDER

  1. Replace the front part of the transmission torque converter and set the transmission to the engine.

If the converter is first set to the motor when setting the gearbox may be damaged O-ring transmission.

  1. Install the transmission control cable and adjust as follows.
    1. Move the selector lever and the transmission range switch in position N and install the control cable transmission.
    2. When connecting the control cable mounting bracket to the transmission, select the clip so that it came into contact with the cable management.
    3. Adjusting nut, select any free wheeling in the control cable and check that the selector lever moves smoothly.
    4. Check that the control cable is properly adjusted.
  1. Install in the reverse order of removal.




« previos page
Replacement of an oil sealing ring of a power shaft		 next page »
Removing and installing transmission A4AF3

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.