REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Touareg (from 2003 to 2006, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Volkswagen
	Touareg
		Operation and maintenance of car
		Engine
		Transmission
		Chassis
		Steering Gear
		Brakes
		Onboard electric
			Overview
				Types of batteries
				Checking the battery
				Topping up with distilled water
				Check the density of the electrolyte
				Check the open circuit voltage battery
				Disconnecting and connecting the battery, vehicles with one battery
				Disconnecting and connecting the battery (vehicles with two batteries)
				Removing and installing the battery, under the driver's seat
				Removing and installing the battery cut-off relay
			Generator and starter
			Device combination
			Front wiper
			Headlights
			Tables
		Body
		diagrams

printable version

Disconnecting and connecting the battery, vehicles with one battery

Disconnecting the battery

Gently push the facing panel down while ago.

NOTE

To disconnect the battery must be deactivated anti-theft alarm system.

Unscrewing the negative terminals of the battery (the cessation of current in the circuit) - Secure working on electrical equipment. Unscrew the positive terminal is only necessary for removing the battery.

Turn the ignition and all electrical consumers and remove ignition key.

Removing the paneling under the driver's seat

Fig. 7.4. Catches wall panel

NOTE

Catches A cling transverse stretching under the seat (Fig. 7.4).

Hold the panel in this position and in the locking tabs A. Pull it up to release.

Catches B fall into the grooves in the transverse stretching in front of the seat. Unlock they can also be by pushing down and pulling over.

Catches C cling to the side facing panel seat, pulling on themselves, they can unlock.

Set the seat to the back, the top position.

Fig. 7.5. Unlock retainers

Unlock clips by pressing down and back at the same time. In this position, lift the facing panel in the clamps (Fig. 7.5).

Push the facing panel down and simultaneously pull it out.

Fig. 7.6. Raising the front panel

Gently lift the cover 1 using a screwdriver from the front panel facing the axis of seat adjustment (Fig. 7.6).

Fig. 7.7. Removing the front panel

Remove the front panel axis seat adjustment with seat slide (Fig. 7.7).

Set the seat to the front, the top position.

NOTE

Removing and installing the rear cladding panels axes seat adjustment is carried out equally on both sides.

Fig. 7.8. Raising the rear panel

Gently lift the cover 1 using a screwdriver from the rear wall panel axis seat adjustment (Fig. 7.8).

Fig. 7.9. Removing the back panel

Remove the back cover of the axis adjustment of the seat with the seat slide (Fig. 7.9).

Release clamps facing the side of the console seat with a screwdriver and remove the panel by pulling it up.

Fig. 7.10. Unlock panel

Unlock the panel (Fig. 7.10).

Fig. 7.11. Fixing screws

Remove the mounting bolts (Fig. 7.11).

Fold the base of the seat with the seat back itself.

Fig. 7.12. Bolt air

Remove the bolt 1 and remove the duct 2 (Fig. 7.12).

Fig. 7.13. Locks, latches

Unlock the battery drawer latches arrow and remove the cover (Fig. 7.13).

Remove the negative terminal and the positive terminal of the battery terminals.

Connecting battery

Put the positive terminal to the positive terminal of the battery.

ATTENTION

Wear pole terminals hand without effort, to prevent damage to the housing of the battery.

Do not lubricate the battery terminals.

Tighten the fixing screw the positive terminal to the specified torque

Only after the positive terminal has been fixed, it is possible to put on the negative terminal to the appropriate battery cable.

Tighten the screws negative terminal to the specified torque.

Replace the base of the seat mounting bolts and tighten them to the specified torque

« previos page
Check the open circuit voltage battery

next page »
Disconnecting and connecting the battery (vehicles with two batteries)