REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Jeep Grand Cherokee (from 1993 to 1999, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Jeep
	Grand Cherokee
		Introduction
		Adjustment and routine maintenance
		The straight six-cylinder engine
		The V8 engine
		Procedure of the general and engine major repairs
		Systems of cooling, heating and air conditioning
		The power supply system and exhaust
		The system of electric motor
		Systems of decrease in toxicity of the fulfilled gases and engine management
		Manual box of a gear change
		Automatic Transmission
		Transfer Case
		Clutch and transmission line
		Brakes
		Suspension and steering
			general information
			Removing and installing front stabilizer lateral stability and bushings
			Removal and installation of the front shock absorbers
			Removal and installation of the transverse jet bar front suspension
			Removal and installation of the front suspension arms
			Removing and installing coil spring front suspension
			Removing and installing steering knuckle
			Replacement ball joints
			Removing and installing rear stabilizer rod transverse stability
			Removing and installing the rear shock absorbers
			Removal and installation of the transverse jet bar rear suspension
			Removal and installation of levers of a back suspension
			Removing and installing coil spring rear suspension
			Removing and installing steering wheel
			Condition check, removal and installation of steering gear
			Removal and installation of the steering mechanism
			Removal and installation of the pump system hydrostrengthening steering
			Bleeding the steering system hydrostrengthening
			Wheels and tires - general information
			Corners of installation of forward wheels - the general information
		Body
		The system of on-board electrical equipment
		Controls and operation receptions

printable version

Suspension and steering

Specifications

The corners of the front axle

The convergence of the front wheels

16	+1.5	mm	(0 ?� 14 '	12 '	)
	-16			-14'

Slay

-0 ?� 15 '	45 '
	-thirty'

The longitudinal tilt axis of the front wheels

7 ?� ?� 30 '

The maximum angle of rotation of the outer wheel to turn

33 ?�

Efforts of a tightening of carving connections, N ??? m

Front suspension

Shock absorbers
The upper nut	19.0
Lower nut	19.0
Stabilizer of transverse stability
Nut stabilizer bar to a connector (front)	37
Bolts of collars of plugs of the stabilizer	54
Bolts and nuts suspension arms
The top lever (both ends)	75
The lower arm (round trip)	176
Transverse torque rods
Nut stud ball joint to an arm frame	81
Bolt / nut on the bracket axle housing	75
Nuts of fastening of the steering knuckle to the Ball joint fork axle beam (with a forked end)	102

Rear suspension

Shock absorbers
The upper nut	71
Lower nut	60
Stabilizer of transverse stability
Nut stabilizer bar to a connector (front)	37
Bolts of collars of plugs of the stabilizer	54
Bolts and nuts suspension arms
The top lever (both ends)	75
The lower arm (round trip)	176
Transverse torque rods
Bolt / Nut jet bar to the frame rail bracket	100
Bolt / Nut jet bar to an arm bridge	100

Steering

Nut fixing the steering wheel hub on the shaft of the column	34
Nuts of fastening of the steering mechanism	88
Nut bipod to the steering mechanism	251
Nut steering pitman arm to the average steering draft	75
Nut middle steering rod to the steering knuckle	47
Nut connecting rod to the middle	75
Nut connecting rod to the steering knuckle	49
Nuts of collars of fastening of the regulator (s) of the steering rod (rod)	49
Nut steering damper actuator to the average steering draft	47
Bolt steering linkage damper bracket to the bridge	75
Wheel nuts	See. Chapter Settings and maintenance

« previos page
Replacement of boots of a lay brake (disc brakes rear wheels)

next page »
general information