Windows

3. Remove the cover of the internal handle.

1. Remove the single screw.
2. Uncover the internal handle.

4. Remove the door trim.

1. Remove the single screw from the bracket knobs.
2. Remove the two screws on the right side of the door trim.
3. Remove the two screws and remove the cover from the left side of the door trim.
4. Remove the two screws from the bottom of the door trim.
5. Separate door trim from the door.
6. Disconnect the electrical connector.

5. Remove the internal handle of opening of the door.

1. Disconnect the two drafts from the door lock.
2. Remove the two screws that secure the door handle.

6. Remove the two screws that secure the bracket knobs.

Shoot pylevlagozaschitnuyu film very carefully in order that it can be reused.

8. Remove the glass.

• Reconnect the connector to the power window switch.
• Attach the wire to the negative terminal of the battery.
• Turn on the ignition and move glass in a half-open position.
• Switch off the ignition.
• Remove the glass run.
• Remove the two screws on the glass to the window regulator.

• Tilt and lift the back part, remove glass from the outside of the door.
• Disconnect the negative battery terminal.

9. Remove the window regulator.

1. Disconnect the connector from the power window motor.
2. Loosen seven nuts window to the door.
3. Through the opening in the inner door panel, remove windows.

10. Remove the door lock.

1. Disconnect the two drafts from the outside door handle.
2. Disconnect the connector from door lock modulator.
3. Remove the two nuts modulator door lock.
4. Remove one screw securing the cover pull the inside door handle.
5. Remove the three screws and remove the door lock.

11. Remove the outer door handle.

• Disconnect the connector from the cylinder of the lock of the door.
• Remove the two mounting screws on the outside door handles.
• Remove the door lock cylinder from the outside door handle.

• Press down on the handle (A) and turn the lower part of the handle outwards and upwards (B).

12. Turn out two nuts of fastening directing glasses.

13. Remove the door speaker.

1. Disconnect the electrical connector.
2. Remove the four screws that secure the speaker to the door.

14. Remove the outside rearview mirror.

1. Disconnect the electrical connector.
2. Remove the three screws and remove the mirror.

15. Remove the harness.

1. Disconnect the harness connectors from the door frame.
2. Remove the wiring harness through the hole in the inner door panel.

17. Remove the two screws and remove the hinges from the door of the car.

5. Install the outside rearview mirror.

1. Install the outside rearview mirror on the door to its original position.
2. Secure the mirror three bolts.
3. Connect the electrical connector.

8. Install the outside door handle.

1. Install the outside door handle through the opening in the inner door panel in the initial position.
2. Install the door lock cylinder on the outside of the door handle.
3. Screw the two mounting screws on the outside door handles.
   Torque: 7-11 N ??? m
4. Connect to the door lock cylinder.

9. Install the door lock.

1. Install the door lock through the opening in the inner door panel.
2. Secure the door lock with three screws.
   Torque: 8-11 N ??? m
3. Screw one screw that secures the cover of the internal handle of traction.
4. Screw the two mounting nuts modulator door lock.
5. Connect the two thrust to the outside door handle.
6. Connect to the modulator of the door lock.

10. Install windows.

1. Install the window regulator through the opening in the inner door panel.
2. Secure windows seven nuts.
3. Connect the window motor electrical connector.

11. Install the glass. Insert the outside of the door at first a forward part of the glass, and then, turning and lowering, set the glass on the door and place it on the bracket window.

1. Screw, but do not lock the two screws on glass.
2. Reconnect the power window control switch.
3. Attach the wire to the negative terminal of the battery.
4. Turn on the ignition and move the window up and down to activate the window control.
5. If necessary, adjust the position of the glass.
6. Switch off the ignition.
7. Disconnect the power window control switch.
8. Disconnect the negative battery terminal.
9. Tighten the two screws on the glass to the window regulator.
   
   Torque: 8-12 N ??? m

14. Establish an arm of the handle and secure it with two screws.

15. Install the inside door handle.

1. Secure the handle with two screws.
2. Connect to handle two thrust the door lock.

16. Install the door trim.

1. Connect the electrical connector.
2. Refit the door trim.
3. Replace the two screws that secure the base of the door trim.
4. Install the cover on the left side of the door trim and secure it with two screws.
5. Replace the two screws that secure the right side of the door trim.
6. Screw one screw bracket handle.