 printable version
Control equipment
1 - tachometer,
2 - Coolant temperature,
3 - pointer to fuel supply,
4 - a speedometer, | 5 - Electronic clock with digital display or trip computer display,
6 - a field indicating the position of the selector,
7 - meter track with service indicator |
Location of control devices depend on the particular car model and engine type.
1 - Tachometer
Tachometer needle in any case should not go into the red zone of the scale. The early switch to a higher gear saves fuel and reduces noise of the engine and transmission! Switch to a lower gear should be as late as possible, shortly before the time when there will be jerks in the engine. During the running of the engine should be avoided with a high engine speed.
2 - Coolant temperature
The index works at the included ignition. When you turn on the ignition for a few seconds, blinks when the health check warning light (s). and - low temperature zone Avoid high engine speeds and not to give the engine a big load! b - zone normal operating temperature During normal driving the pointer must be in the middle area of the scale. At high engine loads and high ambient temperatures, may from time to time entry arrow in the upper zone of the scale. This should not cause concern as long as flashes warning light (s).
with - warning light
If during movement warning light flashes, it is necessary first of all to see what temperature indicates coolant temperature. If the needle is in the area of normal operating temperature, should be at the earliest opportunity to add coolant to the cooling system. If the needle is in the right area of the scale, this means that the coolant temperature is too high. It should stop the car, stop the engine and determine the cause of raising the temperature of the coolant.
3 - index of a stock of fuel
The index works at the included ignition. The capacity of the fuel tank of the car is about 62 liters. If the pointer reaches the red zone a reserve stock of fuel at the same time warning lamp lights up d, this means that there are still about 7 liters of fuel.
4 - Speedometer
5 - Electronic clock with digital display
To set the current time, rotate the button. This button is located at the bottom right around the tachometer. Turn the knob anti-clockwise sets the clock. With a single button, turning a short-term rearrangement of one hour. When you turn the key and hold it in this position there is a continuous rearrangement of hours. Turn the key clockwise until it stops set minutes. With a single button, turning a short-term rearrangement of one minute. When you turn the key and hold it in this position there is a continuous rearrangement of minutes. With this button you can set the clock with the second accuracy: - Turn the button to the right until the clock does not show the time by one minute less than the reference clock;
- Button to instantly turn to the right when the second hand control hours with the exact course will reach a full minute.
5 - Analog clock with indication arrow
Watches with an arrow display located at the bottom of the tachometer. By drawing mounting the button set the current time. The button is located at the bottom right around the tachometer. By briefly pulling the button, the gradual movement of the arrow by the minute. If the button is extended and held in this position by first arrows moved slowly and then increases the speed of their movement. 5 - Display trip computer
Trip computer display (multi-pointer MFA), along with an indication of the current time even gives a lot more information: - The temperature of outside air;
- Instantaneous fuel consumption;
- Average fuel consumption;
- Distance traveled;
- Average speed;
- Travel time. Icon shows the currently parameter appears except this time, at the upper limit of the display field.
| Alternate removal more information on the display when the ignition is carried out by briefly pressing the key balancer B, located on the handle of the windscreen wiper. |
If you click on the upper bound of the key indications of various sizes will be replaced one after another. If you click on the lower bound of the key indications of various sizes will be replaced one by one in reverse order.
Aggregators
Trip computer is equipped with two automatic store: The drive to store information for individual trips (MFA 1) accumulates in itself after the ignition is switched off until it following data on the trip: the movement, the distance traveled and the amount of fuel consumed. On the basis of these data, calculate the average speed, instant and average fuel consumption. If within two hours after the ignition is switched off the car traffic was resumed, new data is added to the former and are included in the calculation of averages. At the break in driving lasting more than two hours, all the data in the drive will be deleted automatically. The drive to store information on the total mileage (MFA 2) accumulates in the car all the data for any number of journeys until a totals value of 100 hours of driving 10,000 kilometers and 1,000 liters of fuel consumed. The accumulated data is used to calculate the results obtained for all trips Our average fuel consumption and speed. When one of these limit values are exceeded, data storage on total run is erased, and the countdown begins again. The drive is in contrast to the drive for a separate trip does not erase the data after two hours of break in driving. To request information should contact the appropriate drive by pressing the A key on the steering column switch Windshield teley. In the field of the clock with digital display appears the corresponding figure for the selected drive: MFA 1 - (drive to store information on individual trips) MFA 2 - (storage for storing information on the total distance covered). From drives, you can call the following indicators: - The average fuel consumption;
- Distance traveled;
- Average speed;
- Driving.
Erasing data drives
If you hold down the key more than two seconds And, the data in the selected drive will be erased. When disconnecting the battery contained in both drives is erased.
Indications
When the ignition is switched on the display shows directional signs "MFA 1" or "MFA 2" depending on whether the drive has been previously selected.
No icon - the current time. Display current time and disappears when you turn off the ignition. Setting the time it is done by turning the setting button beside the tachometer on the combination of the instrument panel.
Outside air temperature FROM Reading range from -40 ?� C to + 58 ?� C. When the vehicle is stationary or moving at a very slow speed shown by the outdoor temperature may be somewhat higher than the true value because of the influence of the thermal radiation of the engine. On vehicles equipped with air conditioning "Climatronic" outdoor temperature is displayed on the screen of the installation, so you can not ask for multi-pointer on the value of the outside temperature. After turning off the ignition has the final reading of the ambient air temperature in the drive still about 3 hours. If after this time the ignition is turned on or prior to the expiration of this time, the car will go on for 3 hours at a speed of about 20 km / h, the display will show the updated value of the outdoor temperature.
A warning  When you largest outdoor temperature to draw conclusions about the possibility of icing of the road, keep in mind that at temperatures above zero degrees may be ice on the road.
Instantaneous fuel consumption 1/100 km Showing fuel currently in liters per 100 kilometers. The calculation of the instantaneous fuel consumption is made through the 30 meters run. The vehicle is stationary holds the last reading of the instantaneous fuel consumption. If selected after the engine fuel flow indicator instant the first 30-40 meters of the motion will show the value of the average fuel consumption. With instantaneous fuel consumption readings can adjust their driving style according to the desired fuel consumption.
Average fuel consumption
Lights average specific fuel consumption and the fuel consumption amount is not currently. This indicator is displayed starts immediately after coating tridtsatimetrovoy distance from the point where data has been erased in the appropriate drive. Prior to that, instead of numbers on the screen touches. While driving my highlights indicator is updated every five seconds. When the selected drive to store information for individual trips (MFA 1) the display shows the average fuel consumption for this trip. When storage for storing information on the total mileage (MFA 2) the display shows the average fuel consumption of all recent trips.
The amount of fuel used is not shown.
Distance traveled km When the selected drive MFA 1 on the display running after ignition, or cleaning the drive. When the selected drive MFA 2, the display shows the mileage on all individual journeys. The maximum value that can be indicated is 9999 km. If the mileage exceeds this value, it starts counting from zero
Average speed km / h All that is stated in paragraph "Fuel consumption" is true for the item "average speed".
Moving time
All that is stated in paragraph "Distance traveled" true for the 'traveling time. "
The maximum value of the reading is 99 hours and 59 minutes. When this value is exceeded again, starting from zero.
6 - Display zone position of the selector of an automatic transmission This shows the position in which there is a selector of an automatic transmission. 7 - Trip odometer / counter of daily run
The top counter indicates the total mileage of the car, the lower - run a certain point (the counter of daily run). The latter figure is lower meter readings means hundred-meter intervals. Zeroing the bottom of the counter is made by pressing the speedometer. 7 - Service indicator
When the time comes for regular maintenance on the lower counter (the counter of daily run) speedometer one of the following designation of the required form of maintenance: - Oil change service OEL or service Oil;
- Service inspection service INSP. Approximately one minute after the start of the engine disappears reading notation necessary maintenance. You can also include the reading of daily run by pressing and holding the button for more than 0.5 seconds setting button daily counter. Service company Volkswagen, which makes the maintenance work after the service indicator is set to the original position. If the service was not performed in the service enterprise a Volkswagen, service indicator should be set to the initial position in this order: - With the ignition off, press and hold down the reset button under the speedometer;
- Switch on the ignition and release the zeroing button only when the display shows the strokes - one of the required type of image service;
- Setting the clock minute button with digital display, turn right (at the clock to pull the arrow indication button). The display shows "service -";
- Switch off the ignition. Only now produced initial setting to indicate the need for maintenance.
In any case, you need to install only the required type of service. Otherwise, the time required service will be indicated incorrectly. Press the setting button, you can select a separate type of service. Do not attempt to zeroing in between two Maintenance - the device will give incorrect readings. When the battery disconnected mileage readings are stored after maintenance. If after repair the speedometer replaced, you must re-program the service indicator. This operation must be carried out in the service enterprise a Volkswagen. If the service indicator is not re-programmed, it is necessary to carry out maintenance work on a vehicle on the "Service Booklet", rather than the service indicator.
| 
