Backdoor

3. Remove the cover of the internal handle.

1. Remove the single screw securing the bracket of the internal handle of opening of the door.
2. Uncover the internal handle.

4. Remove the door trim.

1. Remove the single screw from the bracket knobs.
2. Remove the cover and unscrew the two screws on the left side of the door trim.
3. Remove the two screws on the right side of the door trim.
4. Separate door trim from the door.
5. Disconnect the electrical connector from the power window switch.

5. Remove the internal handle of opening of the door.

1. Disconnect the two drafts from the door lock.
2. Remove the two screws that secure the door handle.

6. Remove the two screws that secure the bracket knobs.

Shoot pylevlagozaschitnuyu film very carefully in order that it can be reused.

8. Remove the outer moisture proof strip and the door trim.

1. Remove the three screws that secure the decorative overlay door.
2. Separate the outer moisture proof strip to the outer side of the door.

9. Remove the glass.

1. Reconnect the connector to the power window switch.
2. Attach the wire to the negative terminal of the battery.
3. Turn on the ignition and move glass in a half-open position.
4. Switch off the ignition.
5. Remove the glass run.
6. Remove the two screws on the glass to the window regulator.
7. Tilt and lift the back part, remove glass from the outside of the door.
8. Disconnect the negative battery terminal.

10. Remove the window regulator.

1. Disconnect the connector from the power window motor.
2. Loosen seven nuts window to the door.
3. Through the opening in the inner door panel, remove windows.

11. Remove the door lock.

1. Remove one nut from the outside door handle.
2. Disconnect the connector from door lock modulator.
3. Remove the two nuts modulator door lock.
4. Remove the three screws, and through the opening in the inner panel of the door, remove the door lock.

12. Remove the outer door handle.

• Remove the two screws on the outside door handles.

• Press down on the handle (A) and turn the lower part of the handle outwards and upwards (B).

13. Remove the two screws on the guide glass.

15. Remove the bolt stop opening the door to the body.

16. Remove the two screws and remove the hinges from the door of the car.

5. Install the glass run.

1. Refit the glass through the opening in the inner door panel.
2. Fix the glass with two bolts.

6. Install the outside door handle.

1. Install the outside door handle through the opening in the inner door panel in the initial position.
2. Replace the two screws on the outside door handles.

Torque: 7-11 N ??? m

7. Install the door lock.

1. Install the door lock through the opening in the inner door panel.
2. Secure the door lock with three screws.
   Torque: 8-11 N ??? m
3. Connect to the modulator door lock
4. Screw the two mounting nuts modulator door lock.
5. Connect craving for outside door handle.

8. Install windows.

1. Install the window regulator through the opening in the inner door panel.
2. Secure windows seven nuts.
3. Connect the window motor electrical connector.

11. Install the glass.

1. Insert the outside of the door at first a forward part of the glass, and then, turning and lowering, set the glass on the door and place it on the bracket window. Screw, but do not lock the two screws on glass.
2. Reconnect the power window control switch.
3. Attach the wire to the negative terminal of the battery.
4. Turn on the ignition and move the window up and down to activate the window control.
5. If necessary, adjust the position of the glass.
6. Switch off the ignition.
7. Disconnect the power window control switch.
8. Disconnect the negative battery terminal.
9. Tighten the two screws on the glass to the window regulator.

Torque: 8-12 N ??? m

11. Install the outer moisture proof strip and the door trim.

1. Secure the outer moisture proof strip on the outside of the door.
2. Replace the three screws that secure the decorative overlay door.

13. Establish an arm of the handle and secure it with two screws.

14. Install the inside door handle.

1. Secure the handle with two screws.
2. Connect to handle two thrust the door lock.

15. Install the door trim.

1. Connect the electrical connector.
2. Refit the door trim.
3. Install the cover on the left side of the door trim and secure it with two screws.
4. Screw one screw securing the right side of the door trim.

16. Screw one screw bracket handle.