 printable version
Adjusting seat
Elements of the mechanical drive adjustment of the front seat (1 of 2) The design of the actuator allows for flexible adjustment to the parameters of the six seats, - use the appropriate section of the switch Button put in the memory / recall parameter adjustment of seats The front seats general information The seat must be set in position, ensuring maximum comfort for the driver to control the pedals, steering wheel and switch on the instrument panel. In addition, the need to provide good visibility through the windshield and reliability of fixing the body of the driver seat belt.
The rear center console is equipped with an adjustable folding armrest of the front seats or armrest, combined with console storage compartment lid.
Adjusting the seat must be carried out before the start of the movement.
Do not use any extra pillows and other items, puts on a cushion or seat back.
Remember that excessive inclination of the seat back in a substantially reduces the efficiency of the belt! Mechanical drive seat adjustment Elements of the mechanical drive control the position of the front seats are located under the cushion (seat adjustment lever in the longitudinal direction) and the outside of the cushion / backrest (tilt and backrest cushions).
Pull the front of the seat under the mite control lever (1) and slide the seat assembly to the desired position. After finishing the adjustment, release the lever and make sure of reliability of fixing the seat by moving it back and forth.
Tilt the seat cushion is made with the lever (2) - Pull the lever up and expand the pillow so that it can provide soft support for thighs.
Tilting backrest is adjusted using the rotary knob (4) mounted in the outer side wall of the backrest.
Increasing the height of the headrest is done by pulling it up from the back of the guide. To lower the headrest should press the button (4) releasing the retainer rails. The slope of the headrest is adjusted manually by turning it forward or backward. Description of the procedures for removing and installing the front head restraints are described in Section Controls and interior equipment. The electric drive of adjustment of seats Switches adjust the position of the front seats are located on the outer sides of the seat assembly. The operation of the electric is only possible at positions 1 and 2 of the ignition switch (on some models in the 0 position when you open any of the front doors).
The design of the actuator allows the adjustment of settings for up to four seats.
In addition, the possibility of entering up to three sets of parameters chosen in memory of the onboard processor, followed by a quick call to the stored data.
For entering the settings in memory processor seat must click access memory (5), and then, with a delay of no more than 3 seconds - any of the three function buttons (6).  | In parallel with the parameters of the seats in the memory of the processor entered installation parameters rear-view mirrors (see. Section Controls and interior equipment). |
Calling memorized processor settings made by holding the corresponding functional buttons. | Before calling the tuning parameters after pre-folding seats, bring it back to the upright position. |
Adjusting the position of the headrest is made by hand, as well as on the seats with a mechanical drive (see. Above). Rear bench seat In order to increase the luggage compartment on these models provides the possibility of sliding the car and the folding rear bench seat. Sliding the seat assembly To release the latch assembly seat, pull on the side wall of the cushion lever, then slide the seat assembly to the desired position.  | The handle is released, the lock assembly rear bench seat |
Folding back | Fold the right and left sections of the back the rear bench seat can be made on an individual basis. |
 | Release button locking rear seatback |
If necessary, the seat back can be folded forward - move the front seat forward (see. Above), remove the rear headrests (see. Section Controls and interior equipment), move the forward assembly of the rear seat (see. Above), then pulling up release button, lower the appropriate section of the backrest, - track tripping latch lock back in the folded position (red mark on the button should not be visible).
Remove head restraint should be removed in special pockets under the floor cover luggage compartment.
When you return back to the upright position track reliability snaps into place - red marking on the button should not be visible. Folding the seat assembly | Fold the right and left sections of the assembly of the rear bench seat can be made on an individual basis. |
Folding down Move the front seat (see. Above) and remove the rear chashkoderzhatel (see. Section Controls and interior equipment).
Lower the rear seatback (see. Above).  | Releasing the latch assembly of the rear seat |
Unlock the seat using the handle (1) while pulling the handle (4) in the direction of the arrow (5), then press the assembly seat down until it clicks into the lock. Folding up To tilt the seat up and pull the handle (1). Fold the right section to provide access to the third row of folding seats Move the right front seat (see. Above), slightly forward, slide the rear seat (see. Above), go back down and lower the front right rear headrest.
Unlock and fold the front right-hand section of the rear seat back (see. Above).  | Handle (6) releasing the retainer right section of the rear seat |
Pull up the handle (6) and fold the right-hand section of the seat forward, lifting it from the rear edge.  | To return to the right-hand section of the rear seat in a regular situation should be lowered rear edge |
Return to the starting position of the seat is made by squeezing the rear edge of the build-down, - track reliability snaps into place.
Return to the upright position of the seat (see. Above) and adjust as required headrest - adjustable rear headrests made similarly to the front (see. Above). Folding seats optional third row Reduction in working position Pre dismantling folding third-row seat (see. Below), remove the luggage compartment floor cover (see. Section Equipment luggage).  | Release fasteners folding seat |
To loosen the fastening of the belt turn the turnbuckle (1) to a horizontal position, unhook the belt hook (2), and using a tape "Velcro" strap attach to the underside of the seat.
Lower back down until it clicks.
Pull the handle (3), release the lock and fold back up, having tracked reliability snaps into place. Replace the back of the headrest, - removal, installation and adjustment of the head restraint folding seats is made similarly to the corresponding procedures for the head restraints of the front and rear seats (see. Section Controls and interior equipment).  | Translation backrest folding seat to the upright position |
Bringing in the stowed position Remove the headrest and fix it on the seat cushion, pull the lock lever (3) to lower the seatback until it clicks. Pull the loop (4), lift the seat upright and hook the hook (2) of the fastening strap. Pull the free end, tension the belt. Dismantling  | Removing the folding seat of the third additional series |
To loosen the fastening of the belt turn the turnbuckle (1) to a horizontal position, unhook the belt hook (2), and using a tape "Velcro" strap attach to the underside of the seat.
Push up the handle (5) releasing the lock and remove the seat assembly.
Installation is in the reverse order - track correctness of getting seats in receptacles and reliability it snaps into place.
| 
