 printable version
Switches
A warning  Before removing a switch remove a wire of weight from the battery and re-connect it to the battery only after the installation of the switch.
Light switch and proof headlights
Location clamps light switch
Removing the bottom panel of furnish of the panel of devices from outside the driver
| 1 - side cover,
2 - lower trim panel,
3 - the switch of light,
4 - Leveling headlights
The arrows mark the location of the screws bottom panel finishes. |
| PERFORMANCE ORDER | | 1. Remove the decorative cover from the left end of the dashboard. See Fig. Removing the bottom panel of furnish of the panel of devices from outside the driver. | | 2. Remove the screws holding the bottom of the instrument panel trim on the driver and remove it. | | 3. Disconnect the electrical connectors from the light switch (3) and corrector of light of headlights (4). See Fig. Removing the bottom panel of furnish of the panel of devices from outside the driver. | | 4. Squeeze the tabs on the light switch (arrow) and, moving it forward and remove the bottom panel of furnish of the panel of devices from outside the driver. See Fig. Location catches the light switch. | | 5. To install, insert the light switch in the tracks at the bottom furnish of the panel of devices from outside the driver and press it until it snaps into place. | | 6. When installing the headlights corrector push it to the back of the snaps into place. | | 7. Connect the electrical connectors to the light switch and equalizer headlights. | | 8. Install the lower finish of the dashboard on the driver side. |
|
CONTROL SWITCH DOOR
Location of screws securing the hatch control switch
| PERFORMANCE ORDER | | 1. Remove the lens. To do this, insert the blade of a knife or other similar object into the slot between the housing and rasseivate Lemma and gently pry the lens. | | 2. Remove the screws holding the switch. See Fig. Arrangement of screws of fastening hatch control switch. | | 3. Disconnect the electrical connector and remove the switch. | | 4. Set the switch is made in sequence, return to removal. |
|
Window switch on the driver
Location screws electric window on the driver's door
Direction release latch and disconnect the electrical connector
Window switches on the driver door formed as a unit, and when a fault is necessary to replace the entire unit.
Rear door power window switch
Removing the rear door power window switch
| A - window switch
In - body |
| PERFORMANCE ORDER | | 1. Remove the inner rear door trim. | | 2. Disconnect the electrical connector from the power window switch. Click on the side surface of the switch (A) and remove it from the slot in the housing of the internal handle of opening the door. See Fig. Removing the rear door power window switch. | | 3. Insert until it clicks into window switch is in the socket body of the internal handle of opening of the door. | | 4. The further installation is made in sequence, return to removal. |
|
WINDOW SWITCH ON THE FRONT PASSENGER DOOR
The direction of squeezing the latches to remove the window switch (A) of the front passenger door
DECORATIVE CAPS INSTRUMENT PANEL
A warning Catches decorative attachment plugs are located on the two longitudinal sides of the plug.
| PERFORMANCE ORDER | | 1. In order to avoid scratching the instrument panel when removing the decorative caps, tape the area around the plug. |  | 2. Using a thin blade screwdriver or a knife, pry the bezel blank and remove it from the dashboard. |
|
SWITCHES hazard warning lights, rear window defogger AND OTHER
Removing the key switches the hazard warning lights
Mount switches is carried out the same way.
To avoid scratching the instrument panel when removing the switch, tape the area around the switch.
| PERFORMANCE ORDER | | 1. Using a thin blade screwdriver or knife inserted under the short side of the key switch and remove the key switch, see. Fig. Removing the key switches the hazard warning lights. |  | 2. pliers, remove the switch from the instrument panel. | | 3. Disconnect the electrical connector from the switch. | | 4. When the switch connect it to the electrical connector and secure it with a clamp. | | 5. Slide the switch in the dashboard slot until it locks. | | 6. Set the key lock switch until it clicks. |
|
SWITCH CAPS LOCK fuel filler
| PERFORMANCE ORDER |  | 1. Insert the blade of a thin screwdriver or a knife into the body of the switch and push and pull the switch of the center console. | | 2. Disconnect the electrical connector from the switch. | | 3. When the switch connect it to the electrical connector and secure the catch. | | 4. Insert the switch in the center console slot until it clicks into the lock. |
|
|
