printable version

Removal and installation of ceiling upholstery (Universal model)

Details of the installation of the ceiling upholstery on models the Versatile (1 of 5)

1, 2 - Sun visors 3 - Bolt 4 - Support 5 - Holder 6 - Cover 7 - Salon rear view mirror	8, 9 - Panels of furnish of racks A B25 - Microphone System Hands-free devices N70 - Switch panel roof console

Details of the installation of ceiling trim Touring models (2 of 5)

10 - Leather 11 - Covers	22 - cargo net mounting points 23 - Bolt

Details of the installation of the ceiling upholstery on models the Versatile (3 of 5)

12 - Support salon mirrors 13, 16 - Screws 14 - Connector wiring	15 - Chrome lining 19 - Metal clip B38 - Rain Sensor

Details of the installation of ceiling trim Touring models (4 of 5)

17 - Screws 18 - Guide	20 - Loosen the screws

Details of the installation of the ceiling upholstery on models Universal (5 of 5)

19 - Metal clip	21 - Roof padding

PERFORMANCE ORDER

Fully open the top hatch. On models corresponding complete set (code ET2) activate the service mode of the emergency call TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE). Remove the left front seat to the frame (see. Section Removal and installation of the assembly of the front seats). Turn on the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last. 7 - Auxiliary battery 8 - terminal positive wire module 9 - negative terminal wire module W10 - Ground Battery Expand the sides, remove from the support arms (4) screws (3), with appropriate equipment disunite wiring connector and remove the sun visors (1 and 2). Remove below the cover (6) fixing screws and remove the clips (5) sun visors (1 and 2). Remove the switch (N70) overhead console (see chap. Onboard electric equipment). Remove the salon mirror (7) (see. Section Removal and installation of salon mirrors). On models corresponding complete gently pry and release of the ceiling upholstery (21) Microphone (B25) of the device Hands-free / Linguatronic, ie disconnect the microphone wiring. Remove the assembly from the rear seat backrest (see. Section Removal and installation of the assembly of the front seats). Remove the panel (8 and 9) finishing racks A (see. Section Removal and installation of the panels finish touring racks). Remove the trim panels in the racks (see. Section Removal and installation of the panels finish touring racks). Remove the side panel trim (see. Section Removing and installing trim panels). Remove the rear cabin lights (see chap. Onboard electric equipment). Remove the upper rear panel trim (see. Section Removing and installing trim panels). Turn located under the cover (11) fixing bolts and remove the top of the handle (10). With proper configuration, remove the mounting screws (23) and remove the attachment points of the cargo net (22). Remove the rear lights designed (see chap. Onboard electric equipment). Remove the bolts (13) Disconnect the connector (14) of the rain sensor (B38) and remove the support bracket (12) interior rearview mirror. Remove the trim cover of the top hatch (see. Section Removing and installing trim panels cover the upper hatch). Remove the six screws (16) and remove the chrome trim (15) on the frame of the top hatch. Remove the bolts (17) of both rails (18) of the top hatch. Gently peel off the cover (21) of the ceiling panel at the points of bonding in the area of the top hatch opening. Release the metal clips (19) and release the cover (21) of the hatch opening. Remove the bolts (20) securing the roof trim (21). Separate the cover (21) from the Velcro fasteners (arrows) and slide diagonally backwards and remove from the vehicle. Installation is in the reverse order - track correctness of electrical contact (3) of the sensor in the sample (4). Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).