printable version

Removing and installing center console

The models 463.250 / 323/333

Details of the installation center console models 463,250 / 323/333 (1 of 5)

1 - cover mounting fuse box	10 - The central console

Details of the installation center console models 463,250 / 323/333 (2 of 5)

85 - Facing frame 86 - Wood Panel 87 - Bolts S4 / 3 - Switch additional heating system (diesel models only)	S46 / 10 - switch heating / ventilation of salon independent action (with appropriate equipment) S97 / 5 - Switch transfer case

Details of the installation center console models 463,250 / 323/333 (3 of 5)

8, 11 - Bolts

Details of installation of the central console (all models) (4 of 5)

5 - Console deflectors 6 - Cover	14 - Catches A - Chashkoderzhatel

Details of installation of the central console (all models) (5 of 5)

6 - Cover 7 - The power outlet	9 - phone connector

PERFORMANCE ORDER

Remove the screw located at the bottom and remove the cover of the assembly block of safety locks (1). Remove the side bolts (arrows) fastenings of the central console (10), - to provide access to the bolts slide into a comfortable position front seat. On models corresponding complete set (code ET2) activate the service mode of the emergency call TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE). Remove the key from the ignition. Turn on the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last. 7 - Auxiliary battery 8 - terminal positive wire module 9 - negative terminal wire module W10 - Ground Battery Remove the lining frame (85) cover the base of the lever of selector AT. Remove the screws (87) located inside the console storage compartment. Gently release the console from the assembly (10) of the front wooden panel (86). Disconnect the electrical wiring from the console switches (S4 / 3, S46 / 10 and S97 / 5). Remove the mounting bolts (8). Uncover the cocking lever parking brake. Carefully release the latches (14) and remove the assembly (5) rear console vents of heating / ventilation of salon. Remove chashkoderzhatel (A). Release the four clamps (two above and two below) and remove the cover (6). Disconnect the electrical wiring from the wall outlet (7). Disconnect the telephone connector (9). Remove the bolts (11). Cock a lay brake. Remove the center console assembly (10), and feeds it back up. Installation is in the reverse order - with the appropriate configuration (code ET2) deactivate service mode of TELE AID (see. Section Activate / deactivate the service mode of the emergency call AID TELE). Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).

The models 463.246 / 249

Corresponding illustrative material submitted for interfacing. Illustrations and graphics Details of the installation center console models 463,250 / 323/333 (2 of 5), and details the installation of the central console models 463,250 / 323/333 (3 of 5), which include all the links in the text.

Details of the installation center console models 463.246 / 249 (see. Also illustrate the details of the installation of the central console (all models) (4 of 5) and details the installation of the central console (all models) (5 of 5))

1 - Cover 2 - Catches 3 - Cover parking brake lever 5 - Console deflectors 6, 8 - Covers 7 - The power outlet 9 - Connector	10 - Command-assembly 11 - Telephone plug 12 - Aerial cable 13 - Lock S97 / 5 - Switch transfer case

PERFORMANCE ORDER

Remove the key from the ignition. Turn on the auxiliary battery and connect it to a standard battery, then disconnect the negative cable last. 7 - Auxiliary battery 8 - terminal positive wire module 9 - negative terminal wire module W10 - Ground Battery Remove the cover (3) cocking lever parking brake. Remove chashkoderzhatel (A). Carefully release the latches (14) and remove the assembly (5) rear console vents of heating / ventilation of salon. Release the four clamps (two above and two below) and remove the cover (6). Disconnect the electrical wiring from the wall outlet (7). Inside the console storage compartment remove the cover (8) and disunite a socket (9). Release of the console assembly connectors (9 and 11) and the antenna cable (12), a pre-release clamps (13). Remove the fourteen mounting screws and remove the assembly center console (10). Installation is in the reverse order. Finally, make the DTC reading and clearing of system memory on-board self-diagnostic scanner using STAR DIAGNOSIS (6511 1801 00) (see chap. Systems of an electric motor).