add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Elantra (from 2000 to 2004, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks
Hyundai Elantra
Home
 
Hyundai
Elantra
Gasoline engines 1.6, 1.8 and 2.0 liters
eleven Technical specifications of petrol engines
Compression Test
Toothed belt
Adjusting the tension of the toothed belt
Adjusting V-belt tension
Adjusting the tension of the alternator drive belt
Camshafts
Check and adjustment of backlashes of valves on engines of 1.8 and 2.0 liters (MLA)
Hydraulic jacks of backlashes of valves of the engine of 1,6 l
Install the cylinder head cover
Chain guide
Chain
Installation of camshafts
The mechanism of change of the moment of opening and closing of valves (CVVT) on engines of 1.8 and 2.0 liters
Repair of a head of cylinders
Engine Supports
Removing and installing engine and gearbox
Cylinder block
Crankshaft
Flywheel
Piston
Air filter (ACL)
An exhaust manifold
Intake manifold
Exhaust
Troubleshooting
The diesel engine of 2.0 liters
Greasing system
Cooling
Fuel system
Control systems and emission control
Ignition system
The system of preliminary heating of the diesel engine
Coupling
Manual transmission
Automatic Transmission
Drive shafts, front and rear axles
Suspension
Steering
Brakes
Body
The air conditioning system
Electrical equipment
Electrical diagrams
 


Hit Counter by Digits


print page printable version

Hydraulic jacks of backlashes of valves of the engine of 1,6 l



PERFORMANCE ORDER

  1. While hydraulic valve clearance compensator is installed in the cylinder head and press it with a maximum intensity at a location where the camshaft comes in contact with a compensator gap. If the compensator gap is OK, it will move downward with great difficulty.
  1. If pressing the compensator gap is easily moved down, it is faulty and must be replaced. Fill the hydraulic jacks of backlashes of valves with engine oil, keep upright and your fingers to squeeze the two sides.

The basic malfunctions of hydraulic jacks of backlashes of valves, causes and solutions are listed in the table.

Malfunction
Possible causes
Remedy
??? Temporary noise when starting from cold Normal The noise disappears after warming up the engine oil and achieve a normal pressure
??? Continuous noise after the engine was not started within 48 hours Oil leaked from the chambers of hydraulic jacks of backlashes of valves, and they hit the air The noise will disappear after 15 minutes of engine operation when the crankshaft reaches a speed of 2000-3000 min -1


Do not increase the engine speed of the engine above 3000 min -1, as this may damage the hydraulic jacks of backlashes of valves.

??? Continuous noise after starting the engine and replace the cylinder head Insufficient oil in the engine oil ducts
??? Continuous noise after a long start-up starter motor or towed Oil leaked from the chambers of hydraulic jacks of backlashes of valves, and they hit the air
??? Continuous noise after replacing the hydraulic jacks of backlashes of valves
??? Continuous noise at the frequency of idling after driving at high speed The engine oil level is too low or too high Check the engine oil level
A large amount of air dissolved in the oil after high speed Check the oil supply
Deterioration of motor oil Check the oil and, if necessary, replace it
??? The noise lasts longer than 15 minutes The low pressure in the lubrication system Check the oil and, if necessary, replace it
Defective hydraulic jacks of backlashes of valves Remove the cylinder head and pressing the hydraulic jacks of backlashes of valves, check the value of compression




« previos page
Check and adjustment of backlashes of valves on engines of 1.8 and 2.0 liters (MLA)
next page »
Install the cylinder head cover

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.